Christini AWD 450DS Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 118

background image

Page 13

Maintenance

The Maintenance Schedule specifies how often you should have your motorcycle served, and what things need attention. It is es-
sential that your motorcycle be served as scheduled to retain its high level of safety, dependability, and emission control perform-
ance. Remember, proper maintenance is your responsibility.

PRECAUTION

Make sure the engine is off before you begin any maintenance or repairs.

Exhaust contains poisonous carbon monoxide. Be sure there is adequate ventilation whenever you operate the engine.

Let the engine and exhaust system cool before touching

Be careful when working around gasoline. Keep cigarettes, spark, and flames away from all fuel related parts

MAINTENANCE RULE

Place the motorcycle on the firm level ground using optional work stand or equivalent support

Use genuine or recommend part and lubricants or other equivalents. Parts that do not meet design specifications may cause dam-
age to the motorcycle

Use only metric tools when servicing the motorcycle, metric nuts, bolts, screws are not interchangeable with British fasteners.

Always replace with new gaskets, O-rings, cotter pins, piston pin clips, snap rings, etc after disassemble engine

When tightening bolts and nuts, begin with larger diameter or inner bolt first. Then tighten to specified torque diagonally in incre-
mental steps unless a particular sequence is specified.

Clean parts in cleaning solvent upon disassembly ,lubricate and sliding surface before assembly.

Always inspect all parts for proper installation and operation after reassemble

Route all electrical wires, cables and harness routing as designed.

MAINTENANCE SCHEDULE

Required maintenance schedule is based upon average riding condition. Sustained high speed operation, or operation in unusually
wet or dusty conditions, will require more frequent service than specified in the REQUIRED MAINTENANCE SCHEDULE. See SPECIAL
MAINTANCE SCHEDULE for competition maintenance need.

Perform the Pre-ride inspection at each scheduled maintenance period

Symbol in maintenance schedule means:

I Inspect and Clean , Adjust , Lubricate or Replace if necessary.

C Clean.

R Replace.

A Adjust.

L Lubricate.

* Unless the rider is mechanically qualified and has proper tools, see authorized dealer for service

* * Special maintenance strongly recommend to look for authorized dealer service.

NOTE1. Clean after every ride for dusty conditions

NOTE2. Replace every 2 years. Replacement requires mechanical skill

NOTE3. Replace after the first break-in ride

NOTE4. Inspect after the first break-in ride

NOTE5. Replace the transmission oil once change the clutch plate

«
...
12
13
14
15
16
...
»

Содержание AWD 450DS























































































































Отзывы:

Нет отзывов

Похожие инструкции для AWD 450DS

Бренд: Öhlins Страницы: 8

Бренд: Honda Страницы: 41

Бренд: R&G Страницы: 13

Бренд: KTM Power Parts Страницы: 22

Бренд: KTM Power Parts Страницы: 12

Бренд: KTM Страницы: 7

Бренд: KTM Страницы: 16

125 EXC EU 2014

Бренд: KTM Страницы: 27

2010 250 EXC-F AUS

Бренд: KTM Страницы: 125

2009 250 EXC-F SIX DAYS

Бренд: KTM Страницы: 125

Бренд: KTM Страницы: 89

Бренд: KTM Страницы: 208

85 SX 17/14 2021

Бренд: KTM Страницы: 133

690 Enduro R EU

Бренд: KTM Страницы: 105

Бренд: KTM Страницы: 191

Бренд: VOR Страницы: 102

Бренд: Buell Страницы: 28

Бренд: HYOSUNG Страницы: 74

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды