background image

INST.No.INE-454-P2 Software 

Ver.1.2

 

- 8 - 

1) To program the analog output minimum value, press 

SEL

 

key in the engineering mode screen until “

OutL

” appears in 

the sub display

 

as shown in the right figure.   

2) By pressing 

 key, the most significant digit of the main 

display will blink.   

3) Use 

or 

key to program the desired value. 

4) To shift to the next lower digit, press 

 key.   

The next lower digit will blink. 

5) Repeat the above procedure of (3) and (4) up to the least 

significant digit for programming (4 digits).   

6) To activate this programming, press 

ENT

 key. 

1) To program the analog output maximum value, press 

SEL

 

key in the engineering mode screen until “

OutH

” appears in 

the sub display

 

as shown in the right figure.   

2) By pressing 

 key, the most significant digit of the main 

display will blink.   

3) Use 

or 

key to program the desired value. 

4) To shift to the next lower digit, press 

key. The next lower 

digit will blink. 

5) Repeat the above procedure of (3) and (4) up to the least 

significant digit for programming (4 digits).   

6) To activate this programming, press 

ENT

 key. 

 

4. Engineering mode

 

In the measurement mode, press 

SEL

 and 

ENT

 keys simultaneously to display the engineering 

mode screen.

 

Refer to the engineering mode screen in [6.3 Parameter programming/selection 

(Engineering mode)]

 

 
 
 
 
 
 
 

4.1 Analog output scaling programming 

4.1.1 Analog output minimum value programming…"OutL" 

This programming is for the minimum value of the temperature scaling when the measured value is 
outputted by analog signal.   

   

 

 

 

 

 

 

 

 
 
 
 

4.1.2 Analog output maximum value programming…"OutH" 

This programming is for the minimum value of the temperature scaling when the measured value is 
outputted by analog signal.

 

 
 
 
 
 

 

 

 

 

 

 

    Tb   CONT   MEM   PEAK

 AL

AH

C
F

ε

 

[Minimum value] 

Caution

To return to the measurement mode screen from the engineering mode screen 

•  

The screen

 

will be automatically returned to the measurement mode screen if 

any key is not pressed for 1 second in the programming of each parameter. 

• 

The screen will return to the measurement mode screen when the 
programming from [4.1 Analog output scaling programming] to [4.10 Analog 
output correction programming] is completed.   

Note

: Up to [4.11 Analog input programming] in case of IR-CAQ

5

 

           

Up to [4.12 Communications programming] in case of IR-CAQ

S

Main display 

Sub display

Tb   CONT   MEM   PEAK

AL

AH

C
F

ε

[Maximum value] 

Main display 

Sub display

• The programmable range is 

0

 to 

6280ºC

• The defaults is 

OutL

 (Minimum value)… Minimum value of the measuring range

Reference

• The programmable range is 

0

 to 

6280ºC

• The defaults is: 

OutH

 (Maximum value)… Maximum value of the measuring 

Reference

4. Engineering mode   

Содержание IR-CA series





































Отзывы: