CHIKO AIRTEC CBA-1300AT2 Скачать руководство пользователя

Страница: 16 / 20

チコーエアーテック株式会社

6.4

ヒューズの交換

Replacement of fuses

交換ヒューズ

CBA-1300AT2

10A

個

CBA-1300AT2-T

個

CBA-1300AT2

（

200V

）

個

6.5

日常点検

Daily inspection

点検項目

Inspection item

頻度

Frequency

点検内容

Description

フィルタケース

Filter case

運転前

Before operation

完全に閉じているか

Is the case closed completely?

排気の状態

Exhaust status

１回／日

Once/day

排気口が閉ざされていないか

Is the exhaust port unclogged?

本体の振動

Vibrations of main body

１回／日

Once/day

異常振動、異常音がないか

設置レベルは出ているか

Are no abnormal vibrations or sounds
generated?
Is the installation level correct?

フィルタの取り付け状態

Filter installation status

１回／月

Once/month

フィルタ取り付けが緩んでいないか

Are the filters installed securely?

フィルタ目づまり状態

（吸引力確認）

Filter clogged status
(Suction force check)

運転時

During operation

吸込みホース端の吸引力は適切か

目詰まりランプが点灯していないか

Does the suction hose end offer proper
suction force?
Is the clogging indicator lamp extinguished?

過負荷により、ヒューズが切れた場合は、ヒューズを交換してください。

When the fuse is blown out by excessive current generated by a

trouble in the internal equipment, replace it.

ヒューズボックスは、

引き抜くことができません

It is impossible to pulled
out the fuse box.

先の細いもので引き出して下さい

Pull it out with the thin thing of
tip.

■

黒いボックスを引き出し、
中に入っているヒューズを交換してください

Pull the black box provided on the MAIN POWER switch,
and replace the fuse.

■

ヒューズは、主電源の下にあります。

The fuse is accommodated inside the black box
provided on the MAIN POWER switch.

Содержание CBA-1300AT2





















Результаты поиска

Содержание CBA-1300AT2

Отзывы:

Похожие инструкции для CBA-1300AT2

Бренды по названию

Популярные бренды

CHIKO AIRTEC CBA-1300AT2, Инструкция по эксплуатации

Результаты поиска

Содержание CBA-1300AT2

Отзывы:

Похожие инструкции для CBA-1300AT2

Бренды по названию

Популярные бренды