Chicago Electric 42933 Скачать руководство пользователя страница 14

Страница: 14 / 24

SKU 42933

For technical questions, please call 1-800-444-3353.

Page 14

ADjuStMentS

The following checks, and possible adjust-

ments, should be done in the order listed

before beginning operation.

WARnIng: For safety, unplug the line

cord to the Radial Arm Saw.

Tables A (127), B (126), and C (125)

are checked for straightness at the

factory.

However, changes in humidity can

slightly alter the condition of the

wood. With the Screw Clamps (131)

tightened, use a straight edge or

framing square to check for flatness

and squareness. Sand down any high

spots using fine sandpaper.

Check for Arm tightness on the Col-

umn (132). If loose, tighten Bolt (115).

3. Check the crosscut travel of the Saw

Blade for squareness.

- Lock or tighten all adjustment levers

and knobs.

- Lower the Arm until it just clears the

Table A front.

- Place a framing square so it just

touches a tooth of the Saw Blade.

- Mark this location with a pencil on

the table and draw a straight line us-

ing the square.

- Check that the Saw blade follows

this line from front to back.

If the Saw Blade moves to the right

or left side of the line as it travels the

entire length of the Arm, loosen the

Screw Clamps (137) and lightly tap

on the Table left or right side until

there is full travel alignment. Tighten

the Screw Clamps again.

4. Check that the Saw Blade is square

to Table A.

- Place a framing

square on Table A

so that the square

is flat on the Saw

Blade (not touching

teeth).

- If there is no gap between the

square and the Saw Blade, no adjust-

ment is necessary.

- If the square does not touch the

Saw Blade evenly (with the square

flat on the Table A), loosen the Bevel

Lock Knob (71) and adjust the motor

until the gap between Saw Blade and

the square is eliminated.

5. Check that the Saw Blade is square

to the rip fence.

- Firmly place a

framing square

against the rip

fence and the blade

as shown to the

right. The square

should not touch any teeth.

- If the square is not flush with the

entire blade, loosen the yoke

pivot Clamp Handle (66) and move

the motor assembly until any gaps

have been eliminated. Tighten the

Yoke Pivot Clamp and recheck align-

ment. (This will simultaneously set

both yoke indexing positions for in

and out ripping.)

Содержание 42933

























Результаты поиска

Содержание 42933

Отзывы:

Похожие инструкции для 42933

Бренды по названию

Популярные бренды

Chicago Electric 42933, Руководство по установке и эксплуатации

Результаты поиска

Содержание 42933

Отзывы:

Похожие инструкции для 42933

Бренды по названию

Популярные бренды