background image

386950CE6CD (07—08) 

5

Fig. 6 

OPERATION

4.  Plug machine’s power cords into grounded wall 

outlets on separate circuits (Figure 3). Green 
circuit indicator light on switch panel illuminated 
confirms connection to separate circuits. 

FOR SAFETY: Do not operate machine unless 
cord is properly grounded. 

FOR SAFETY: Do not operate machine with the 
use of an extension cord. 

5.  Secure recovery tank lid in place. 

MACHINE OPERATION 

FOR SAFETY: Do not operate machine unless 
entire operator manual is read and understood. 

 

PRE-OPERATION 

1.  Inspect power cord for damage. 

2.  Turn on empty-out pump (Figure 4). The 

discharge pump will not come on until the level 
inside the recovery tank activates the float switch. 
Note: the “Auto Discharge” switch must be turned 
on in order for the discharge pump to cycle on 
and off. 

3.  Turn on water faucet supplying water to the 

machine. 

 

CLEANING TILE 

1.  Activate the pressure pump and both vacuum 

switches (Figure 5). 

2.  Apply cleaning chemicals to the surface to be 

cleaned with a separate application sprayer. 
Follow chemical manufacturers instructions for 
selection of chemical and dwell time before 
pressure rinsing with this machine. 

ATTENTION: This machine is designed to deliver 
high pressure fresh water to the tile surface and 
extract emulsified soil. This model is not 
designed to mix chemicals with fresh water. Any 
attempt to do this could damage fresh water 
pump. 

3.  Take hard surface or tile cleaning tool in hand 

and move in the direction that compliments tool 
design intermittently spraying rinsing solution. 

 

WHILE OPERATING 

1.  Periodically check for excessive foam buildup in 

recovery tank. Use a recommended foam control 
solution to prevent vacuum motor damage. 

 Warning: Flammable materials or reactive 

metals can cause an explosion or fire. Do not 
pick up. 

ATTENTION: Excessive foam buildup will not 
activate the float shut-off screen. 

ATTENTION: Discharge pump will not pump foam. 
Use a defoamer. 

 

DRAINING RECOVERY TANK 

1.  Turn off machine after majority of water has been 

pumped out by discharge pump. 

2.  Insert supplied 45º elbow in drain valve. Place a 

bucket below it and slowly pull up on handle 
(Figure 6). 

 

GROUNDED OUTLET 
          (3 hole) 

GROUNDING 
               PIN 

Fig. 3 

Fig. 4 

Fig. 5 

Содержание 386950CE6CD


















Отзывы: