Champion CADRSASP12 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 44

Champion CADRSASP12 Скачать руководство пользователя страница 19

18

GUIDE TO MAINTENANCE

To obtain reliable and satisfactory service, this unit requires a consistent preventive maintenance schedule.
Maintenance schedule pages are included in the back of this manual to aid in keeping the proper records.

Before  performing  any  maintenance  function,  switch  main  disconnect  switch  to  "off"  position  to
assure  no  power  is  entering  unit.    "Lock  Out"  or  "Tag  Out"  all  sources  of  power.    Be  sure  all  air
pressure in unit is relieved.  Failure to do this may result in injury or equipment damage

.

DAILY MAINTENANCE

1.

Check oil level of both compressor and engine if so equipped. Add quality lubricating oil as required.
See Section on "Oil Specifications".

2.

Drain moisture from tank by opening tank drain valve located in bottom of tank. Do not open drain
valve if tank pressure exceeds 25 PSIG.

3.

Check operation of electric tank drain by pushing manual test button located on drain.

4.

Turn off compressor at the end of each day's operation. Turn off power supply at wall switch.

WEEKLY MAINTENANCE

1.

Clean dust and foreign matter from cylinder head, motor, fan blade, air lines, intercooler and tank.

2.

Remove and clean intake air filters.

Do not exceed 15 PSIG nozzle pressure when cleaning element parts with compressed air. Do not
direct compressed air against human skin. Serious injury could result. Never wash elements in fuel
oil, gasoline or flammable solvent.

3.

Check V-belts for tightness

.

The V-belts must be tight enough to transmit the necessary power to the

compressor. Adjust the V-belts as follows:

a. Remove bolts and guard to access compressor drive.

b. Loosen mounting hardware which secures motor to base. Slide motor within slots of baseplate to

desired position.

c. Apply pressure with finger to one belt at midpoint span. Tension is correct if top of belt aligns with

bottom of adjacent belt. Make further adjustments if necessary.

d. Check the alignment of pulleys. Adjust if necessary.

e. Tighten mounting hardware to secure motor on base.

f.

Re-install guard and secure with bolts.

Never operate unit without belt guard in place. Removal will expose rotating parts which can cause
injury or equipment damage.

«
...
17
18
19
20
21
...
»

Содержание CADRSASP12













































Отзывы:

Нет отзывов