Chamberlain Liftmaster Elite LA500 Скачать руководство пользователя страница 23

Страница: 23 / 60

STEP 8 continued...

POWER WIRING

LARGE METAL CONTROL BOX

To use solar panels with the Large Metal Control Box (Model XLSOLARCONTU) skip the steps below and refer to the Solar Panels section in the
Appendix.

1. Unplug the J15 plug labeled BATT(-)(+) DC(-)(+) on the control board by squeezing the plug and pulling it from the control board.

2. Turn off the AC power from the main power source circuit breaker.

3. Run the AC power wires to the control box.

4. Remove the toroid assembly from the control box by loosening the three screws and lifting the assembly up and out.

5. Ensure the 120/240 plug is connected to either the 120 or 240 Vac connector on the EMI board depending on your application. Factory default is

120 Vac.

6. Connect the ground wire to the ground screw on the back of the toroid assembly.

7. Connect the white wire from the toroid assembly to NEUTRAL using a wire nut.

8. Connect the black wire from the toroid assembly to HOT using a wire nut.

9. Replace the toroid assembly and tighten the screws. Ensure the wires are not pinched.

10. Connect a jumper between the positive (+) terminal of one battery to the negative (-) terminal of the other battery.

11. Connect the red wire from the J15 plug labeled BATT (+) to the positive (+) terminal of the battery.

12. Connect the black wire from the J15 plug labeled BATT (-) to the negative (-) terminal of the battery.

13. Plug the J15 plug into the control board. The control board will power up.

NOTE:

You may see a small spark when plugging the J15 plug into the

board.

14. Turn ON AC power.

INSTALLATION

(back view of toroid assembly)

(incoming power wires)

NEUTRAL

HOT

GROUND

White

Black

Ground
Screw

Toroid Assembly

J15 Plug

120 Vac
Connector

240 Vac
Connector

Jumper

Black Wire (-)

Red Wire (+)

LARGE METAL CONTROL BOX (LA500CONTXLMU)

Содержание Liftmaster Elite LA500




























































Результаты поиска

Содержание Liftmaster Elite LA500

Отзывы:

Похожие инструкции для Liftmaster Elite LA500

Бренды по названию

Популярные бренды

Chamberlain Liftmaster Elite LA500, Руководство по установке

Результаты поиска

Содержание Liftmaster Elite LA500

Отзывы:

Похожие инструкции для Liftmaster Elite LA500

Бренды по названию

Популярные бренды