Chamberlain Liftmaster Elite LA500 Скачать руководство пользователя страница 34

Страница: 34 / 60

LOCKS

ACCESSORY WIRING

MISCELLANEOUS WIRING

SINGLE BUTTON CONTROL (SBC)

(2 Terminals)

Gate command sequence - Open, Stop, Close, Stop,...

Soft open (maintained switch does not override external safeties and does
not reset alarm condition).

FIRE DEPARTMENT OPEN INPUT

(2 Terminals)

Acts as hard open.

Maintained input overrides (ignores) external safeties (photoelectric
sensor and edge), pauses Timer-to-Close momentary input logic as single
button control and safeties remain active, re-enables Timer-to-Close.

ACCESSORY POWER 24 VDC, MAX 500 mA

(4 Terminals)

•

SWITCHED: Switched ON with gate motion (stays on 5 seconds after

motion).

•

UNSWITCHED: 24 Vdc voltage out to power accessories, always ON.

MAGLOCK

(2 Terminals, N.C. and COM)

Relay contact output, Normally - closed (N.C.) output for maglocks.

Relay activates prior to motor activation and during motor run. Relay is
off when motor is off.

SOLENOID

(2 Terminals, N.O. and COM)

Normally - open (N.O.) output for solenoid locks

Relay activates prior to motor activation and during motor run. Relay is
off when motor is off.

NOTE:

To conserve power for solar applications, the lock relay will only

activate for four seconds near the close limit.

Com

SBC

(main control board)

Single Button
Control Station

Fire Department

Acc Power +24 Vdc

Com (-)

(main control board)

Maglock

(not provided)

(control board)

Accessory Power Unswitched

Accessory Power Switched

Acc Power +24 Vdc

Com (-)

Com

Fire Dept

Solenoid Lock

(not provided)

Содержание Liftmaster Elite LA500




























































Результаты поиска

Содержание Liftmaster Elite LA500

Отзывы:

Похожие инструкции для Liftmaster Elite LA500

Бренды по названию

Популярные бренды

Chamberlain Liftmaster Elite LA500, Руководство по установке

Результаты поиска

Содержание Liftmaster Elite LA500

Отзывы:

Похожие инструкции для Liftmaster Elite LA500

Бренды по названию

Популярные бренды