Chamberlain Liftmaster Elite LA500, Руководство по установке

Страница: 29 / 60

27
GATE OPERATOR SETUP EXAMPLES
The following are example setups for the gate operator. Your specific site requirements may be different. Always setup the operator system to the site
requirements, including all necessary entrapment protection devices.
RESIDENTIAL: One to four residential homes sharing a gated entrance/exit, allowing vehicle access trumps security concerns
COMMERCIAL/GENERAL ACCESS: A residential community (more than four homes) having one or more gated entrances/exits, allowing vehicle
access trumps security concerns
COMMERCIAL: Business site where security (gate closed) is important
INDUSTRIAL: Large business site where security is required
SETTING RESIDENTIAL COMMERCIAL/GENERAL ACCESS COMMERCIAL INDUSTRIAL
Quick Close switch
setting
Normally set to OFF.
Normal gate close (timer
or control). Normally set to OFF. Normal gate
close (timer or control). Normally set to OFF.
Normal gate close (timer
or control). Set to ON, so that gate
closes immediately after
vehicle passes interrupt
loop.
AC Fail switch
setting Normally set to BATT.
Run on battery if AC
power fails. Normally set to BATT. For local
jurisdiction requirement, set to OPEN so
that the gate will open approximately 15
seconds after AC power fail. Normally set to BATT.
Run on battery if AC
power fails. Normally set to BATT. Run
on battery if AC power fails.
Low Battery switch
setting Normally set to OPEN. If
powered from battery and
battery is low, gate
automatically opens and
stays open. Normally set to OPEN. If powered
from battery and battery is low, gate
automatically opens and stays open. Normally set to CLOSE. If
powered from battery and
battery is low, gate stays
closed.
Normally set to CLOSE. If
powered from battery and
battery is low, gate stays
closed.
Anti-Tail switch
setting Normally set to OFF.
Interrupt loop reverses a
closing gate. Normally set to OFF. Interrupt loop
reverses a closing gate. Set to ON. In attempt to
prevent vehicle tail-gating,
interrupt loop pauses a
closing gate. Set to ON. In attempt to
prevent vehicle tail-gating,
interrupt loop pauses a
closing gate.
Bipart Delay switch
setting For DUAL-GATE site, set
to ON for gate that delays
upon opening. For DUAL-GATE site, set to ON for
gate that delays upon opening. For DUAL-GATE site, set
to ON for gate that delays
upon opening. For DUAL-GATE site, set to
ON for gate that delays
upon opening.
Aux Relay Out –
Open Limit Switch Typically not required. Use with SAMS (Sequence Access
Management System). 1) Use with SAMS
(Sequence Access
Management System)
2) Connect “Gate Open”
indicator (e.g. light)
1) Use with SAMS
(Sequence Access
Management System)
2) Connect “Gate Open”
indicator (e.g. light)
Aux Relay Out –
Close Limit Switch Typically not required. Typically not required. Connect “Gate Close/
Secure” indicator (e.g.
light). Connect “Gate Close/Secure”
indicator (e.g. light).
Aux Relay Out –
Gate Motion
Attach alert signal
(audible or visual alert
system). Attach alert signal (audible or visual
alert system). Attach alert signal (audible
or visual alert system). Attach alert signal (audible
or visual alert system).
Aux Relay Out –
Pre-Motion Delay Attach alert signal
(audible or visual alert
system). Attach alert signal (audible or visual
alert system). Attach alert signal (audible
or visual alert system). Attach alert signal (audible
or visual alert system).
Aux Relay Out –
Power Attach visual alert to
know when system is
charging batteries (i.e.
not running on batteries). Attach visual alert to know when
system is charging batteries (i.e. not
running on batteries). Attach visual alert to know
when system is charging
batteries (i.e. not running
on batteries). Attach visual alert to know
when system is charging
batteries (i.e. not running
on batteries).
Aux Relay Out –
Tamper Attach alert signal
(audible or visual alert
system) to indicate if gate
is manually tampered
with by being pushed off
of close limit. Attach alert signal (audible or visual
alert system) to indicate if gate is
manually tampered with by being
pushed off of close limit. Attach alert signal (audible
or visual alert system) to
indicate if gate is manually
tampered with by being
pushed off of close limit. Attach alert signal (audible
or visual alert system) to
indicate if gate is manually
tampered with by being
pushed off of close limit.
Cycle Quantity
Feedback Use during servicing only
to determine operator
cycles.
Use during servicing only to determine
operator cycles. Use during servicing only
to determine operator
cycles. Use during servicing only to
determine operator cycles.
Fire Dept Open input
Typically not required. Connect emergency access system
(Knox box switch, SOS system, etc.) Typically not required. Typically not required.
OPERATION