Chamberlain DDO8900W Скачать руководство пользователя

Страница: 16 / 32

Green

Ground

Screw

Ground Wire

Black Wire

Wire Nuts

(Not Provided

White Wire

Flexible

Conduit

90˚

Connector

(Not

Provided)

Green Wire

White Wire

Black Wire

BACK VIEW

Connect Power

Installation

OPTION B: PERMANENT WIRING

CONNECTION

If permanent wiring is required by

your local code, refer to the following

procedure.

To make a permanent connection through

the 7/8" hole in the back of the door

operator (according to local code):
1. Be sure power is NOT connected to

the door operator, and disconnect

power to circuit.

2. Remove the door operator from the

torsion bar, remove cover screws and

set the cover aside.

3. Cut the line cord 6" (15.2 cm) above

the strain relief.

4. Squeeze the strain relief and push

into motor unit, then remove the

strain relief from the line cord.

5. Install a 90° conduit (not provided)

or flex cable adapter (not provided) to

the 7/8" hole. Reinstall door operator

to torsion bar.

6. Run wires through conduit, cut to

proper length and strip insulation.

7. Strip 1/2" (1.3 cm) of insulation from

the existing black, white and green

wires.

8. Connect the line to the black wire and

neutral to the white wire with wire

nuts (not provided). Connect ground

wire to the green ground screw.

9. Properly secure wires under plastic

ties so that they do not come into

contact with moving parts.

10. Reinstall cover.

To avoid installation difficulties, do not

run the door operator at this time.

To reduce the risk of electric shock, your

door operator has a grounding type plug

with a third grounding pin. This plug will

only fit into a grounding type outlet. If the

plug doesn’t fit into the outlet you have,

contact a qualified electrician to install the

proper outlet.

There are two options for connecting

power:

OPTION A: TYPICAL WIRING

1. Plug in the door operator into a

grounded outlet.

2. DO NOT run door operator at this

time.

To prevent possible SERIOUS INJURY or DEATH from electrocution or fire:
• Be sure power is NOT connected to the operator, and disconnect power to circuit

BEFORE removing cover to establish permanent wiring connection.

• Door installation and wiring MUST be in compliance with ALL local electrical and

building codes.

• NEVER use an extension cord, 2-wire adapter or change plug in ANY way to make it

fit outlet. Be sure the operator is grounded.

RIGHT

WRONG

RIGHT

WRONG

Ground Tab

Green

Ground Screw

Ground Wire

Black Wire

PERMANENT WIRING

CONNECTION

White Wire

Black

Wire

Ground Tab

Green

Ground Screw

Ground Wire

Black Wire

PERMANENT WIRING

CONNECTION

White Wire

Black

Wire

RIGHT

WRONG

RIGHT

WRONG

Ground Tab

Green

Ground Screw

Ground Wire

Black Wire

PERMANENT WIRING

CONNECTION

White Wire

Black

Wire

Ground Tab

Green

Ground Screw

Ground Wire

Black Wire

PERMANENT WIRING

CONNECTION

White Wire

Black

Wire

WRONG

RIGHT

Содержание DDO8900W
































Результаты поиска

Содержание DDO8900W

Отзывы:

Похожие инструкции для DDO8900W

Бренды по названию

Популярные бренды

Chamberlain DDO8900W, Руководство пользователя

Результаты поиска

Содержание DDO8900W

Отзывы:

Похожие инструкции для DDO8900W

Бренды по названию

Популярные бренды