Chamberlain DDO8900W страница 11 Скачать руководство пользователя | Manualshive

Страница: 11 / 32

background image

11

Install door control within sight of door, out of reach of small children at a

minimum height of 5 feet (1.5 m) above floors, landings, steps or any other

adjacent walking surface, and away from ALL moving parts of door.

1. Remove the control station cover.
2. Fasten the control station to the wall at least 5' (1.5 m) above floors, landings,

steps or any other adjacent walking surface. The installation surface must be

smooth and flat.

3.   Select appropriate knockout and run the wires to the operator.
4.   Connect wires to the control station and replace the control station cover.
5.   Fasten the warning placards to the wall next to the three button control station.

NOTE:

DO NOT connect the power and operate the door operator at this time. The door

will travel to the full open position but will not return to the close position until the

safety reversing sensors are connected and properly aligned. See page 12.

Install the Three Button Control Station

5

Installation

To prevent possible SERIOUS INJURY or

DEATH from electrocution:
• Be sure power is NOT connected

BEFORE installing door control.

• Connect ONLY to 24 VOLT low voltage

wires.

To prevent possible SERIOUS INJURY or

DEATH from a closing door:
• Install door control within sight of door,

out of reach of children at a minimum

height of 5 feet (1.5 m) above floors,

landings, steps or any other adjacent

walking surface, and away from ALL

moving parts of door.

• NEVER permit children to operate or

play with door control push buttons or

remote controls.

• Activate door ONLY when it can be seen

clearly, is properly adjusted and there are

no obstructions to door travel.

• ALWAYS keep door in sight until

completely closed. NEVER permit anyone

to cross path of closing door.

1 2 3 4 5 6 7 8 9 10 11 12 13 14

To insert or

release wire,

push in tab with

screwdriver tip

Three Button

Control Station

132A2112-2

132LA2112-20-A
Shown at 100% (4.25" x 2.375")
ECN: 07-0326
14-May-2007

DO NOT EXCEED 10 DOOR OPERATIONS
PER HOUR.
FASTEN LABEL ADJACENT TO DOOR.

NE PAS FAIRE FONCTIONNER LA PORTE
PLUS DE 10 FOIS PAR HEURE.
FIXER L’ÉTIQUETTE PRÈS DE LA
PORTE.

40-35246-10-A
Shown at 100%
ECN: 09-2104
4-May-2009

«
...
9
10
11
12
13
...
»

Содержание DDO8900W

































Отзывы:

Нет отзывов

Похожие инструкции для DDO8900W

Бренд: National Comfort Products Страницы: 28

Бренд: Novetec Страницы: 7

Sentronic 2310-ME

Бренд: LCN Страницы: 2

Бренд: Migatronic Страницы: 28

Бренд: Neutec Страницы: 22

TITANIUM 400 AC/DC

Бренд: GYS Страницы: 120

Fusion splicer 232103

Бренд: Televes Страницы: 24

Бренд: Draper Страницы: 28

Бренд: Eastwood Страницы: 24

Бренд: Dormakaba Страницы: 8

Бренд: Lincoln Electric Страницы: 56

Бренд: Craftsman Страницы: 36

Бренд: Craftsman Страницы: 36

Бренд: Craftsman Страницы: 16

Бренд: Craftsman Страницы: 36

SIRIUS 3RV19 6 2 Series

Бренд: Siemens Страницы: 5

SIRIUS 3RV2926-1B

Бренд: Siemens Страницы: 8

Бренд: Siemens Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды