Chamberlain DDO8900W Скачать руководство пользователя

Страница: 10 / 32

HARDWARE

Attach the Cable Tension Monitor (Required)

NOTE:

The cable tension monitor is shipped for left side installation. It is recommended

that the cable tension monitor be installed on the same side of the door as the door

operator. For right side installation, remove the snap-ring holding the roller in place and

reassemble it on the opposite side of the cable tension monitor.

1. Make sure the door cable is approximately 3/4" (19 mm) from the mounting surface.

Door adjustments or shimming may be required to achieve proper depth for the door

cable.

2. Position the cable tension monitor no more than 6' (2 m) above the door opening,

and be sure the roller extends 1/8"-1/4" past the cable. Make sure cable tension

monitor is located over a wood support member and the roller is free from any

obstructions.

NOTE:

There must be no obstructions in the installation area that prevent the cable

tension monitor from closing completely when slack is detected.

3. Mark and drill 3/16" pilot holes for screws (pilot holes are not required for anchors).

4. Attach the cable tension monitor to the wall using the hardware provided. Make sure

that the roller is on top of the cable.

5. Run bell wire to door operator. Use insulated staples to secure wire.

6. Connect bell wire to the green quick-connect terminals on the door operator (polarity

is not important).

NOTE:

Cable must have tension through entire door travel. Make sure there is no

slack in cable on opposite side of door during normal operation. If slack occurs

during door travel, adjust cables as required.

A second cable tension monitor may be installed for additional security. When two cable

tension monitors are installed, the door will not move in the down direction or will reverse

if one of the monitors detects slack or is disconnected.

If one of the cable tension monitors is removed, unplug both monitors from the operator.

Then plug in the monitor you wish to use and unplug and plug in the operator three times

to relearn the monitor to the operator.

Drum

Cable

To insert or

release wire,

push in tab with

screwdriver tip

(To cable tension monitor)

(To door operator)

WHT/

GRN

Wall

Approx. 3/4"

(19 mm)

Approx. 2.5"

(63.5mm)

IMPORTANT:

Roller must be

placed no more

than 6' (2 m)

above door

opening

Cable

Tension

Monitor

Cable Tension

Monitor Roller

1/8"-1/4"

(3-6 mm)

Installation

The cable tension monitor MUST be

connected and properly installed before

the door operator will move in the down

direction.
The cable tension monitor detects ANY

slack that may occur in the cables and

will reverse the door, eliminating service

calls.

Door Closed

Door Open

Screws

#8-32x1" (2)

Drum

Cable Tension

Monitor Roller

Screw

14-10x2" (2)

The position of

the cable

tension monitor

will vary

depending on

the type of door

and drum used.

Содержание DDO8900W
































Результаты поиска

Содержание DDO8900W

Отзывы:

Похожие инструкции для DDO8900W

Бренды по названию

Популярные бренды

Chamberlain DDO8900W, Руководство пользователя

Результаты поиска

Содержание DDO8900W

Отзывы:

Похожие инструкции для DDO8900W

Бренды по названию

Популярные бренды