manualshive.com logo in svg

Chamberlain DDO8900W, Руководство пользователя

Поделиться
Скачать
Chamberlain DDO8900W Скачать руководство пользователя страница 14

14

Installation

WIRE THE SAFETY REVERSING SENSORS

1.   Run the wire from both sensors to the door operator. Attach the wire to the wall and 

ceiling with the staples.

2.   Strip 7/16" (11 mm) of insulation from each set of wires. Separate the wires. Twist 

the white wires together. Twist the white/black wires together.

3.   Insert the white wires into the white terminal on the door operator. Insert the white/

black wires into the grey terminal on the door operator. To insert or remove the 

wires from the terminal, push in the tab with a screwdriver tip.

MOUNTING THE SAFETY REVERSING SENSORS

1.   Slide a 1/4"-20x1/2" carriage bolt head into the slot on each sensor.
2.   Use wing nuts to fasten safety reversing sensors to brackets, with lenses pointing 

toward each other across the door. Be sure the lens is not obstructed by a bracket 

extension.

3.  Finger tighten the wing nuts. 

HARDWARE

Carriage Bolt

Wing Nut

Wing Nut

1/4"-20 (2)

Carriage Bolt

1/4"-20x1/2" (2)

1 2 3

4 5

6

7 8 9 10 11 12 13

WHT/ 

BLK

WHT

Bell wire

7/16 

(11 mm)

NOTE: 

The door referenced in this image depicts 

standard or high lift applications. If mounting 

this on a vertical lift door, your door will look 

different.

Содержание DDO8900W

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды