Chamberlain DDO8900W страница 21 Скачать руководство пользователя | Manualshive

Страница: 21 / 32

background image

21

TEST

1. With the door fully open, place a 1-1/2" (3.8 cm) board (or a 2x4 laid flat) on the

floor, centered under the door.

2. Operate the door in the down direction. The door MUST reverse when it makes

contact with the board.

ADJUST

If the door stops but does not reverse:
1.  Review the installation instructions provided to insure all steps were followed;
2.   Repeat Program the Travel (see Adjustment Step 1);
3.   Repeat the Safety Reversal test. If the test continues to fail, call a trained door

systems technician.

IMPORTANT SAFETY CHECK:

Test the Safety Reverse System after:
•

Each adjustment of limits.

•

Any repair to or adjustment of the door (including springs and hardware).

•

Any repair to or buckling of the floor.

•

Any repair to or adjustment of the operator.

Test the Safety Reversal System

Test the Protector System

1.   Press the control station button to open the door.
2.   Place the operator carton in the path of the door.
3.   Press the control station button to close the door. The door will not move more than

an inch (2.5 cm).

The door operator will not close from a control station if the indicator light in either sensor

is off (alerting you to the fact that the sensor is misaligned or obstructed).

If the door operator closes the door when the safety reversing sensor is obstructed,

do not operate the door. Call for a trained door systems technician.

Without a properly installed safety

reversal system, persons (particularly

small children) could be SERIOUSLY

INJURED or KILLED by a closing door.
• Safety reversal system MUST be

tested every month.

• After ANY adjustments are made,

the safety reversal system MUST

be tested. Door MUST reverse on

contact with 1-1/2" (3.8 cm) high

object (or 2x4 laid flat) on the floor.

Without a properly installed safety

reversing sensor, persons (particularly

small children) could be SERIOUSLY

INJURED or KILLED by a closing door.

2

3

Safety Reversing Sensor

Safety Reversing Sensor

1-1/2" (3.8 cm) board

(or a 2x4 laid flat)

Adjustments

«
...
19
20
21
22
23
...
»

Содержание DDO8900W

































Отзывы:

Нет отзывов

Похожие инструкции для DDO8900W

Бренд: GAL Страницы: 2

Бренд: Laars Страницы: 9

Бренд: Unimig Страницы: 14

WELDSKILL 200HF

Бренд: CIGWELD Страницы: 60

Digital Car Puller 5000

Бренд: Telwin Страницы: 104

deviflex DTIV-9

Бренд: DEVI Страницы: 8

Бренд: ubbink Страницы: 12

Бренд: Red-D-Arc Страницы: 56

Бренд: Valeo Страницы: 86

Бренд: Punair Страницы: 3

Бренд: Dormakaba Страницы: 10

Бренд: SUGATSUNE Страницы: 4

Lapcon SDS-C301N-BLK

Бренд: SUGATSUNE Страницы: 4

Бренд: Lincoln Electric Страницы: 52

Бренд: LORCH Страницы: 40

Бренд: Stel Страницы: 38

Бренд: Praxair Страницы: 62

ASSA ABLOY 8800 Series

Бренд: Sargent Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды