Challenge 99100 Скачать руководство пользователя страница 3

1.0  Introduction

2

1.0 Introduction

This manual is designed to help you get the most from your Challenge equipment.  Keep this manual
in a safe, convenient place for quick reference by operators and service personnel.

 SAFETY ALERT!  This symbol means CAUTION: Personal safety
instructions!  
Pay special attention to the instructions in bold type.
Personal injury may result if the precautions are not read and followed.

READ THIS MANUAL BEFORE OPERATING!  If you follow precautions and instructions, you should
have years of trouble-free operation.  Contact your Authorized Challenge Dealer.

FOR PARTS AND SERVICE, contact the Authorized Challenge Dealer from whom you purchased
your machine.  Use the illustrations and parts lists at the back of this manual to identify the correct
parts needed.  Always give the SERIAL NUMBER and MODEL of your machine to insure the correct
parts are sent as soon as possible.

Take a few minutes right now to RECORD YOUR MACHINE SERIAL NUMBER in the space
provided on the front cover of this manual.  Also be sure to fill out the warranty card accompanying
this manual and return it DIRECTLY TO CHALLENGE.

If you bought a used machine, it is important to have the following information on record at Challenge.
Copy this page, fill in the information and send it care of The Challenge Service Department, 6125
Norton Center Drive 

 Norton Shores 

 MI  49441-6081.

CHALLENGE MODEL

Spartan 120

SERIAL NUMBER

ATTN

COMPANY

ADDRESS
CITY

STATE/PROVINCE

ZIP

PHONE

DATE INSTALLED

DEALER NAME & CITY

* WARRANTY INFORMATION *

PLEASE REVIEW THE ENCLOSED WARRANTY INFORMATION SHEET

It is very important that you read and understand the conditions outlined in the Warranty Information
Sheet 
attached to the outside of the shipping container of your machine.

The Warranty Information Sheet must be filled out completely and returned to THE CHALLENGE
MACHINERY COMPANY in order for the warranty to be issued for this machine.

Challenge® is a registered trademark of

The Challenge Machinery Company

 6125 Norton Center Drive

 Norton Shores

 MI  49441-6081

Copyright© 2000-2006 by The Challenge Machinery Company.  All rights reserved.  Printed in the USA.

 

 

 

 

 

 

NOTICE: UNSUPPORTED PRODUCT! 

NO TECHNICAL SUPPORT AVAILABLE!

 

NO REPAIR PARTS AVAILABLE! 

 

 

Содержание 99100














































Отзывы: