Century Heating CB00023 Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 56

background image

Page 32

Installation and Operation Manual - FW3200

ENGLISH

8.2 Floor Protection

This stove is designed to prevent the floor from overheating. However, it must be placed on a
nonflammable surface to protect the floor from hot embers that may fall during loading.

The floor protection must be a continuous, non combustible material, such as steel with a
minimum thickness of 0.015" (0.38 mm) or ceramic tiles sealed together with grout. Cement
board, brick, or any other approved or listed material suited for floor protection. No R factor
required.

Any type of tile will require a continuous non combustible sheet beneath to prevent the possibility
of embers falling through to the combustible floor if cracks or separation should occur in the
finished surface. Check local codes for approved alternatives.

No protection is required if the unit is installed on a non-combustible floor (ex: concrete).

FLOOR PROTECTION

Canada

USA

G

18

8" (203 mm)

N/A

H

8" (203 mm)

N/A

I

18" (457 mm)

From door

opening

16" (203 mm)

From door

opening

J

N/A

8" (203 mm)

N

19

N/A

See Note 2

H

I

G

J

Floor Protection

8.3 Reducing Clearances Safely

It is often desired to use as little space as possible
when installing a wood stove. To do this, it is possible
to reduce the clearances safely and install the stove
closer to the walls by permanently installing a heat
shield between the stove and the flammable material.

The rules for heat shields are sometimes complicated.
Read and apply the instructions carefully. Some
regions may have different regulations. Consult the
local building code or contact the fire department for
restrictions, inspection and installation requirements in
the area.

Heat shield

18

The floor protection at the back of the stove is limited to the stove’s required clearance if such clearance is smaller than 8 inches (203 mm).

19

Only required under the horizontal section (Ho) of the connector. Must exceed each side of the connector by at least 2 inches (51 mm).

See "Clearances - Ceiling"

«
...
30
31
32
33
34
...
»

Содержание CB00023

























































Отзывы:

Нет отзывов

Похожие инструкции для CB00023

Бренд: Omega Страницы: 11

Бренд: Cadel Страницы: 352

Бренд: RAIS Страницы: 36

Бренд: Real Flame Страницы: 12

Бренд: Broseley Страницы: 38

Бренд: Bartscher Страницы: 44

GALLERY CLASSIC 5

Бренд: Percy Doughty & Co Страницы: 9

Бренд: SCAN Страницы: 4

Бренд: Clayton Страницы: 32

Бренд: Lifestyle Страницы: 7

Бренд: Blaze King Страницы: 57

Бренд: BFM Страницы: 4

Бренд: Sierra Woodstoves Страницы: 16

Бренд: Royal Страницы: 140

COMPAK EPA EXEMPT DB03060

Бренд: Drolet Страницы: 19

Бренд: Drolet Страницы: 56

Бренд: Palazzetti Страницы: 16

Бренд: Ariterm Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды