Century Heating CB00023 Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 56

background image

Page 23

Installation and Operation Manual - FW3200

ENGLISH

6.3.3 Gasket

The glass gasket is flat, adhesive-backed, woven fibreglass. The gasket must be centred on the
edge of the glass.

1. Follow the steps of the previous section to remove the

glass.

2. Remove the old gasket and clean the glass thoroughly.

3. Peel back a section of the paper covering the adhesive and

place the gasket on a table with the adhesive side up.

4. Stick the end of the gasket to the middle of one edge, then

press the edge of the glass down onto the gasket, taking
care that it is perfectly centred on the gasket.

5. Peel off more of the backing and rotate the glass. The

gasket must not be stretched during installation.

6. Cut the gasket to the required length.

7. Pinch the gasket onto the glass in a U shape, all around the glass.

6.4 Door

In order for the stove to burn at its best efficiency, the door must
provide a perfect seal with the firebox. The tightness of the door
seal can be verified by closing and latching the door on a strip
of paper. The test must be performed all around the door. If the
paper slips out easily anywhere, replace the gasket.

6.4.1 Gasket

It is important to replace the gasket with another having the
same diameter and density to maintain a good seal.

1. Remove the door and place it face-down on something soft

like a cushion of rags or a piece of carpet.

2. Remove the old gasket from the door. Use a screwdriver to

scrape the old gasket adhesive from the door gasket groove.

3. Apply a bead of approximately 3/16" (5 mm) of high

temperature silicone in the door gasket groove. Starting from
the middle, hinges side, press the gasket into the groove.
The gasket must not be stretched during installation.

4. Leave about ½" (13 mm) long of the gasket when cutting and

press the end into the groove. Tuck any loose fibers under
the gasket and into the silicone.

5. Close the door. Do not use the stove for 24 hours.

«
...
21
22
23
24
25
...
»

Содержание CB00023

























































Отзывы:

Нет отзывов

Похожие инструкции для CB00023

Бренд: Yakar Страницы: 14

Studio Stove 14

Бренд: Warmington Страницы: 16

Bayfield GDS25NA-1

Бренд: Wolf Steel Страницы: 96

Бренд: ADURO Страницы: 92

Бренд: ADURO Страницы: 104

Бренд: ADURO Страницы: 92

Бренд: Opus Страницы: 20

Бренд: U.S. Stove Страницы: 35

Бренд: Hi-Flame Страницы: 46

Бренд: Heta Страницы: 12

Бренд: Heta Страницы: 32

SCAN-LIINE 80 XL

Бренд: Heta Страницы: 28

Бренд: Heta Страницы: 26

Fourneau "Rully"

Бренд: Lacanche Страницы: 38

Бренд: Haas+Sohn Страницы: 4

Бренд: England's Stove Works Страницы: 103

Бренд: L'Artistico Страницы: 32

Бренд: MOA Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды