Century Heating CB00023 Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 56

background image

Page 36

Installation and Operation Manual - FW3200

ENGLISH

9. The Venting System

9.1 General

The venting system, made of the chimney and the connecting pipe between the stove and the
chimney, acts as the engine that drives the wood heating system. Even the best stove will not
function safely and efficiently if it is not connected to a suitable chimney.

The heat in the flue gases that pass from the stove and chimney connector into the chimney is
not waste heat. This heat is what the chimney uses to make the draft that draws in combustion
air, keeps smoke inside the stove and safely vents exhaust to outside. The heat in the flue gas
can be seen as the fuel the chimney uses to create draft.

9.2 Suitable Chimneys

This stove will provide optimum efficiency and performance when connected to a 6" diameter
chimney flue system. The connection to a chimney having a diameter of at least 5" (Canada
only) or no more than 7" is permitted, if it allows the proper venting of combustion gases and
that such application is verified and authorized by a qualified installer. Otherwise, the diameter
of the flue should be 6".

To be suitable, a factory-built metal chimney must comply with UL 103 HT (U.S.A.) or ULC S629
(Canada).

9.2.1 Factory-Built Metal Chimneys

These are sometimes referred to as ‘high
temp’ chimneys because they have the specific
characteristics to withstand temperatures that can
be created by wood burning stoves. Factory-built
chimneys are tested as a system with all the necessary
components for installation. The instructions provided
with the chimney by its manufacturer are the only
reliable source of installation guidelines. To be safe
and effective, the chimney must be installed exactly
in accordance with the manufacturer’s instructions.
Only components intended for the brand and model
of chimney should be used. Never fabricate or
substitute parts from other chimney brands. The
chimney must be a type suitable for solid fuel.

«
...
34
35
36
37
38
...
»

Содержание CB00023

























































Отзывы:

Нет отзывов

Похожие инструкции для CB00023

Бренд: BALKAN ENERGY Страницы: 14

Бренд: Quadra-Fire Страницы: 20

Бренд: Quadra-Fire Страницы: 16

RAILROAD POTBELLY PB65XL

Бренд: Northline Express Страницы: 16

Бренд: Zibro Страницы: 12

Бренд: Cleanburn Страницы: 18

Бренд: Kratki Страницы: 108

PHILO Comfort Air

Бренд: MCZ Страницы: 46

Murcia Chimenea Large

Бренд: La Hacienda Страницы: 9

NIMBUS NIM-105N

Бренд: Sawotec Страницы: 19

Бренд: Thelin Страницы: 31

Бренд: COMPANION Страницы: 8

Бренд: United States Stove Страницы: 40

Бренд: MBM Страницы: 195

Бренд: Gasmate Страницы: 2

HF217-SE Baby Gabriel

Бренд: Olymberyl Страницы: 44

Tenorio PowerSystem Compact 23/684

Бренд: Olsberg Страницы: 44

Бренд: Heat-N-Glo Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды