Century Heating CB00023 Скачать руководство пользователя страница 29

Страница: 29 / 56

Page 29

Installation and Operation Manual - FW3200

ENGLISH

8.1 Clearances

APPLIANCE CLEARANCES WITH SINGLE

WALL PIPE CONNECTOR

APPLIANCE CLEARANCES WITH DOUBLE

WALL PIPE CONNECTOR

Canada

USA

Canada

USA

" (368 mm)

" (191 mm)

20" (508 mm)

12" (305 mm)

10" (254 mm)

If the above clearances are met, then the distances measured from the flue outlet will be:

DISTANCES

FROM PIPE CONNECTOR

WITH SINGLE WALL PIPE CONNECTOR

DISTANCES

FROM PIPE CONNECTOR

WITH DOUBLE WALL PIPE CONNECTOR

Canada

USA

Canada

USA

18" (457 mm)

11" (279 mm)

28 ¾" (730 mm)

21 ¾" (552 mm)

19 ¾" (502 mm)

8.1.1 With Heat Shield AC02762

APPLIANCE CLEARANCES WITH DOUBLE

WALL PIPE CONNECTOR

DISTANCES13 FROM DOUBLE WALL PIPE

CONNECTOR

Canada

USA

Canada

USA

3" (76 mm)

6 ½" (165 mm)

3" (76 mm)

11 ¾" (298 mm)

3" (76 mm)

12 ¾" (324 mm)

The pipe distances listed in this table refer to the distances obtained when the stove is installed in accordance with the appliance clearances

above mentioned.

Note that to reduce the clearances of an appliance using a single wall pipe connector, the use of a heat shield certified with the single wall pipe

connector to be used as close as 6" (153 mm) from combustible materials must be used. Only in this case, the same clearances as a certified double

wall pipe connector can be used.

Содержание CB00023

























































Результаты поиска

Содержание CB00023

Отзывы:

Похожие инструкции для CB00023

Бренды по названию

Популярные бренды

Century Heating CB00023, Инструкция по установке и эксплуатации

Результаты поиска

Содержание CB00023

Отзывы:

Похожие инструкции для CB00023

Бренды по названию

Популярные бренды