background image

6

A.

B.

Forward

Side Room Requirement

Your RDO is comprised of 2 major individual components being, Drive Unit (top figure alongside) and
Control Box (bottom figure alongside). This section of the manual deals with the basic fitting
requirements which should be met

you attempt to install your opener. Study them carefully to

ensure that your door and surroundings are suitable for such an installation.

The recommended minimum and maximum door mounting bracket position as measured from the edge
of the garage door curtain is depicted in Fig.5. The ideal distance should be between 85~125mm as
indicated.

before

Important Note: The procedures outlined in this manual require a certain degree of technical and
mechanical skill. It is not recommended that your RDO be installed by a home handyman. The RDO
should always be installed, serviced and adjusted by a technically qualified person.

Important Notes:

The fixing distance may vary from garage door to garage door depending on the distance

thatthe garage door drum wheel has been set inside the garage door curtain.

If the door drum wheel has been set too deep inside the garage door curtain it is recommended

to fit an additional drum wheel closer to the edge of the curtain facilitating easier installation of
the RDO unit.

The installer should verify the correct distance by actually checking the measurement prior to

mounting or moving any garage door brackets.

?

?

?

Fig 5

REQUIREMENTS PRIOR TO INSTALLATION

Содержание CS32 RDO






















Отзывы: