Centsys D2 Turbo Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 46

background image

FIGURE 19.

Off

Gate is closed

On

Gate is partially or fully open

Continuous slow flash

Gate is opening

Continuous fast flash

Gate is closing

Three flashes every two seconds

Battery voltage is low

Four flashes every two seconds

Multiple collisions have occurred



Pre-flashing Mode C

With Pre-flashing Mode C activated, the Pillar Light Relay will activate

  for two seconds before gate movement occurs, as well as during gate
  movement. This means that gate movement will be delayed for a
  period of two seconds after a trigger signal has been received.

To change the Courtesy (Pillar) Light to one of the Pre-flashing Modes, please
refer to the section, 'Customising the Features and Functions' on page 16.

3.1.12. External Gate Status Indication LED

An LED (Light Emitting Diode)
mounted on your intercom
allows you to view the position
of your gate and the condition of
the battery and power supply
from the safety of your home.
The different signals of the LED
are described below:

If you choose not to fit a Gate Status Indicator, the status LED
on the controller can also be used for troubleshooting.

3.1.13. Battery-low Protection

The

D2 Turbo

controller has circuitry that monitors the state of the

battery. During a power failure, energy is drawn from the battery but
not replaced.

To protect the battery from being damaged, the protection circuitry
prevents the motors from being run off the battery when the battery
voltage drops below 10.6V.

Indication that the Battery-low Protection has been triggered is provided
by the onboard buzzer and status LED on the controller (and intercom if
so equipped and connected to the controller). The LED will flash three
times every two seconds, as will the buzzer beep three times every two
seconds. The gate system will also shut off until such time as the
battery has recharged to an acceptable level.

Consult your gate automation specialist or Centurion Systems (Pty) Ltd
if you discover that your Battery-low Protection signal continues to re-
occur.

Features

and

Functions

page 15

«
...
17
18
19
20
21
...
»

Содержание D2 Turbo















































Отзывы:

Нет отзывов

Похожие инструкции для D2 Turbo

Бренд: Langjushan-Tech Страницы: 12

Бренд: IDEAL Страницы: 67

Бренд: Key Automation Страницы: 60

Бренд: SmartPower Страницы: 17

GDO-6v3 EasyRoller

Бренд: Automatic Technology Страницы: 36

Бренд: Chamberlain Страницы: 40

Бренд: Polaris Страницы: 44

Бренд: quiko Страницы: 2

Бренд: Beninca Страницы: 20

Бренд: Abloy Страницы: 32

Бренд: Hamilton Beach Страницы: 2

Бренд: STEELON Страницы: 33

Бренд: Genie Страницы: 2

SCREW DRIVE GARAGE DOOR

Бренд: Genie Страницы: 2

Бренд: DoorKing Страницы: 6

Бренд: Delta Electronics Страницы: 141

Бренд: GTO Страницы: 43

Бренд: OSCO Страницы: 10

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды