Centrometal BioTec-C Скачать руководство пользователя страница 3 | Manualshive

Страница: 3 / 26

Centrometal BioTec-C Скачать руководство пользователя страница 3

3

Description

LANGUAGE SELECTION MENU

MAIN SCREEN

note: this screen is shown for very short time

After turning on the main switch, screen will turn on. Boiler type, power and firmware version will be shown. If language
selection menu is

enabled

, after pressing any key, language selection menu is shown. Select language and press OK

button. If language menu is

disabled

regulation will show for very short time boiler version, power and firmware version

and automatically switch to main screen.

1.1. SWITCHING ON

1.0. DESCRIPTION

1 - Boiler temperature
2 - Flue gas temperature
3 - Flue gas fan rpm
4 - Accumulation tank upper temprature
5 - Working stage
6 - Working stage counters
7 - Error/Warning LED
8 - UP/LEFT button
9 - ESCAPE/BACK/CANCEL button
10 - DOWN/RIGHT button
11 - Flue gas fan symbol

12 - GLOW mode symbol (shown when this mode is enabled)
13 - Return flow temperature (shown only if return flow sensor
is installed and enabled or if protection valve is enabled)
14 - Pump P1 symbol
15 - 3-way mixing valve actuator symbol (if configured)
16 - Mixing valve symbol
17 - Accumulation tank lower temperature
18 - DHW pump P2 symbol (if configured)
19 - Time and date
20 - DHW tank temperature (if configured)
21 - Working LED
22 - OK/CONFIRMATION/ENTER button

Main switch ON
-> Press any key

Select language
and press OK button
to enter main screen

language
selection menu

Screen (full configuration) and buttons

(NOTE: some symbols are shown
only at certain configurations)

boiler model

firmware version

22

21

20

17

18

16

14 15

1

2

3

4

5

6

7

8

9

10

13

12

Language selection menu

ENABLED

Language selection menu

DISABLED

note: this screen is shown for very short time

MAIN SCREEN

LANGUAGE SELECTION MENU

11

19

boiler power

Technical instructions REGULATION

BioTec-C

«
1
2
3
4
5
...
»

Содержание BioTec-C



























Отзывы:

Нет отзывов