Central Machinery 32650 Скачать руководство пользователя страница 10

Страница: 10 / 26

Page 10

For technical questions, please call 1-800-444-3353.

SKU 32650

To install the Height Knob:

Figure 4

Nut (56)
Stud (17)

Washer (18)

a. Unthread the Shipping Nut (56) from the

Stud counterclockwise and remove it

from the Stud.

Washer (18)

Figure 5

Height Knob

(16)

Stud (17)

b. Leave the Washer in place and thread

the Height Knob (16) onto the Stud

clockwise until it is secure.

OPeraTing inSTrucTiOnS

read the enTire iMPOrTanT

SaFeTY inFOrMaTiOn

section at the beginning of this

manual including all text under

subheadings therein before set up

or use of this product.

Tool Set up

TO PreVenT

SeriOuS injurY

FrOM accidenTal

OPeraTiOn:

Turn the Power Switch of the tool

to its “OFF” position, pull out the

Switch key (27b), and unplug the

tool from its electrical outlet

before performing any

inspection, maintenance, or

cleaning procedures.
TO PreVenT SeriOuS injurY:

dO nOT OPeraTe WiTh anY

guard diSaBled, daMaged,

Or reMOVed.

adjusting the Main Spindle height

The Main Spindle (43) can be adjust up

or down by 3/4”.

Figure 6

Height Knob

(16)

Raise

Main

Spindle

Lower

Main

Spindle

To adjust the height of the Main Spindle

(43) turn the Height Knob (16) counter

clockwise and slide the Knob to the left

to lower, or the right to raise, the height

of the Main Spindle. When it is the

desired height, tighten the Height Knob

clockwise until it is secure.

reV 10e

Содержание 32650



























Результаты поиска

Содержание 32650

Отзывы:

Похожие инструкции для 32650

Бренды по названию

Популярные бренды

Central Machinery 32650, Руководство по установке и эксплуатации

Результаты поиска

Содержание 32650

Отзывы:

Похожие инструкции для 32650

Бренды по названию

Популярные бренды