Central Machinery 32650 Скачать руководство пользователя страница 3

Страница: 3 / 26

Page 3

For technical questions, please call 1-800-444-3353.

SKU 32650

SaVe ThiS Manual

Keep this manual for the safety warnings

and precautions, assembly, operating,

inspection, maintenance and cleaning

procedures. Write the product’s serial number

in the back of the manual near the assembly

diagram (or month and year of purchase if

product has no number). Keep this manual

and the receipt in a safe and dry place for

future reference.

iMPOrTanT SaFeTY

inFOrMaTiOn

in this manual, on the labeling, and

all other information provided with

this product:

This is the safety alert

symbol. it is used to alert

you to potential personal

injury hazards. Obey all

safety messages that follow

this symbol to avoid possible

injury or death.

danger indicates a

hazardous situation

which, if not avoided, will result

in death or serious injury.

Warning indicates a

hazardous situation

which, if not avoided, could

result in death or serious injury.

cauTiOn, used with

the safety alert

symbol, indicates a hazardous

situation which, if not avoided,

could result in minor or moderate

injury.

nOTice is used to

address practices not

related to personal injury.

cauTiOn, without the

safety alert symbol, is

used to address practices not

related to personal injury.

general Tool Safety Warnings

Warning read all safety warnings

and instructions.

Failure to follow the

warnings and instructions may result

in electric shock, fire and/or serious

injury.

Save all warnings and instructions

for future reference.

KEEP GUARDS IN PLACE and in

working order.
REMOVE ADJUSTING KEYS AND

WRENCHES. Form habit of checking to

see that keys and adjusting wrenches

are removed from tool before turning it

on.
KEEP WORK AREA CLEAN. Cluttered

areas and benches invite accidents.
DON’T USE IN DANGEROUS

ENVIRONMENT. Don’t use power tools

in damp or wet locations, or expose them

to rain. Keep work area well lighted.
KEEP CHILDREN AWAY. All visitors

should be kept safe distance from work

area.
MAKE WORKSHOP KID PROOF

with padlocks, master switches, or by

removing starter keys.
DON’T FORCE TOOL. It will do the job

better and safer at the rate for which it

was designed.

reV 10e

Содержание 32650



























Результаты поиска

Содержание 32650

Отзывы:

Похожие инструкции для 32650

Бренды по названию

Популярные бренды

Central Machinery 32650, Руководство по установке и эксплуатации

Результаты поиска

Содержание 32650

Отзывы:

Похожие инструкции для 32650

Бренды по названию

Популярные бренды