Central Machinery 32650 Скачать руководство пользователя страница 9

Страница: 9 / 26

Page 9

For technical questions, please call 1-800-444-3353.

SKU 32650

inSTrucTiOnS FOr PuTTing

inTO uSe

read the enTire iMPOrTanT

SaFeTY inFOrMaTiOn

section at the beginning of this

manual including all text under

subheadings therein before set up

or use of this product.

TO PreVenT

SeriOuS injurY

FrOM accidenTal

OPeraTiOn:

Turn the Power Switch of the tool

to its “OFF” position and unplug

the tool from its electrical outlet

before assembling or making any

adjustments to the tool.

note:

For additional information regarding the

parts listed in the following pages, refer

to the Assembly Diagram near the end of

this manual.

assembly/Mounting

Figure 2

Fence (2)

Protective foam sheet

Knobs

(4)

The Shaper/Router is packaged with a

protective foam sheet covering the table

top and the fence, secured in place on

the table. Remove the Shaper/Router

from the box then unthread the Knobs

(4) holding the Half and Long Fence (2a

and 2b) pieces from the Table Top (7).

Discard the foam sheet.

Mounting

Mount the Shaper/Router to a permanent

location such as a work bench, or to a

portable plywood base. If mounting to

plywood, use a good grade of plywood or

chipboard at least 3/4” thick.

Plywood or workbench

Base of Shaper/Router

14-1/8”
10-1/8”

5-1

1/16”

9-1

1/16”

2”

Four 5/16”

Diameter holes

Figure 3

To Mount the Shaper/Router, use the

above dimensions to mark the drilling

locations on the plywood or workbench,

allowing at least 2” of clearance on all

sides. Drill four 5/16” diameter holes and

attach the Shaper/Router using grade 5

or better 1/4” bolts, flat washers and self

locking nuts (sold separately). Be sure

to purchase bolts which are long enough

to reach through the Shaper/Router

Base, the thickness of the Plywood

or workbench top, and allow for the

washers and nuts.

Warning:

If you mount the Shaper/Router

on a portable base, before each use,

clamp the board securely to a workbench

or supporting surface.

installing the height knob

The Stud (17) for the Height Knob (16) is

located on the back of the Base (25) and

is packaged with a Nut (56) and Washer

(18).

reV 10e

Содержание 32650



























Результаты поиска

Содержание 32650

Отзывы:

Похожие инструкции для 32650

Бренды по названию

Популярные бренды

Central Machinery 32650, Руководство по установке и эксплуатации

Результаты поиска

Содержание 32650

Отзывы:

Похожие инструкции для 32650

Бренды по названию

Популярные бренды