Central Machinery 32650 Скачать руководство пользователя страница 5

Страница: 5 / 26

Page 5

For technical questions, please call 1-800-444-3353.

SKU 32650

grOunding inSTrucTiOnS

TO PreVenT

elecTric ShOck

and deaTh FrOM incOrrecT

grOunding Wire

cOnnecTiOn

read and FOllOW TheSe

inSTrucTiOnS:

110-120 V~ grounded Tools: Tools

with Three Prong Plugs

In the event of a malfunction or

breakdown, grounding provides a path

of least resistance for electric current

to reduce the risk of electric shock.

This tool is equipped with an electric

cord having an equipment-grounding

conductor and a grounding plug. The

plug must be plugged into a matching

outlet that is properly installed and

grounded in accordance with all local

codes and ordinances.
Do not modify the plug provided – if it will

not fit the outlet, have the proper outlet

installed by a qualified electrician.

Improper connection of the equipment-

grounding conductor can result in a risk

of electric shock. The conductor with

insulation having an outer surface that

is green with or without yellow stripes is

the equipment-grounding conductor. If

repair or replacement of the electric cord

or plug is necessary, do not connect the

equipment-grounding conductor to a live

terminal.

Check with a qualified electrician or

service personnel if the grounding

instructions are not completely

understood, or if in doubt as to whether

the tool is properly grounded.
Use only 3-wire extension cords that

have 3-prong grounding plugs and

3-pole receptacles that accept the tool’s

plug.
Repair or replace damaged or worn cord

immediately.

125 V~ 3-Prong Plug and Outlet

(for up to 125 V~ and up to 15 a)

grounding

Pin

This tool is intended for use on a circuit

that has an outlet that looks like the one

illustrated above in

125 V~ 3-Prong

Plug and Outlet

. The tool has a

grounding plug that looks like the plug

illustrated above in

125 V~ 3-Prong

Plug and Outlet

The outlet must be properly installed and

grounded in accordance with all codes

and ordinances.
Do not use an adapter to connect this

tool to a different outlet.

Shaper Safety Warnings

For Your Own Safety read instruction

Manual Before Operating Shaper

Wear eye protection.

Be sure keyed washer is directly under

spindle nut and spindle nut is tight.
Feed work piece against rotation of

cutter.
Do not use awkward hand positions.

Keep fingers away from revolving cutter

– use fixtures when necessary.

reV 10e

Содержание 32650



























Результаты поиска

Содержание 32650

Отзывы:

Похожие инструкции для 32650

Бренды по названию

Популярные бренды

Central Machinery 32650, Руководство по установке и эксплуатации

Результаты поиска

Содержание 32650

Отзывы:

Похожие инструкции для 32650

Бренды по названию

Популярные бренды