background image

 

32

 

                   

V3.15.22 

 

Advanced Operation 

CellarPro cooling systems can be programmed with advanced settings to achieve 
more  control  over  conditions  inside  the  cellar.  Conditions  like  humidity,  the 
Temperature  Differential,  and  alarm  settings  all  can  be  modified  for  custom 
applications. To access the advanced settings, do the following: 

 Press  the  “Set”  button  and  the  “Down”  button  together  at  the  same  time,  and 

hold for three seconds. Then, use the “Up” or “Down” button to scroll to the following 
screen: 

 

 

LOW  TEMPERATURE  ALARM: 

The  factory  preset  for  this 

setting is “45”.

 

This setting designates the Low temperature inside the cellar 
at  which  the  alarm  is  triggered.  We  recommend  leaving  this 
setting at the factory preset. 

ENERGY SAVINGS MODE DIFFERENTIAL: 

The factory preset 

for this setting is “4”.

 

This  setting  controls  the  Temperature  Differential  for  the 
Energy  Savings  Mode.  The  recommended  range  for  this 
setting is 2-4.

 

 

 

 

  

HUMIDITY: 

The factory preset for this setting is “3”.

 

If  the  humidity  inside  the  cellar  is  too  low,  press  the  “Set” 
button,  then  use  the  “Up”  button  until  the  desired  setting  is 
reached. The recommended range for this setting is 0-6. 

TEMPERATURE  DIFFERENTIAL: 

The  factory  preset  for  this 

setting is “4”.

 

This  setting  determines  the  Temperature  Differential  and 
therefore the temperature at which the cooling unit will cycle 
on. The recommended range for this setting is 4 or 5. 

HIGH  TEMPERATURE  ALARM: 

The  factory  preset  for  this 

setting is “70”.

 

This  setting  designates  the  High  temperature  inside  the 
cellar at which the alarm is triggered. We recommend leaving 
this setting at the factory preset. 

 

Содержание 3000Shqc-EC







































Отзывы: