CEA TREO 1800 Synergic MIG-MAG, Руководство оператора

Страница: 31 / 42

9
• At the end of the procedure, the software present in the welder
will immediately re-calculate the characteristic curve of the en-
gine, rendering it suitable to use.
WARNING: The motor CANNOT be stopped during the measu-
ring time!
• To exit from the CALIBRATION menu, press and release the
SAVE “MEM” key (T2).
T2
7•V
MIG-MAG synergic
Start the welder by pressing the switch, located on the back pa-
nel, at the position I .
1 - WELDING PROCESS SELECTION
Select the MIG welding PROCESS this way:
1) Pressing and releasing, even various times if necessary, the
WELDING PROCESS SELECTION key (T2) until the corre-
sponding LED lights up.
T2
2) Pressing and releasing, even various times if necessary, the
MIG WELDING PROCESS and PROGRAMME SELECTION
key (T2) until the corresponding LED lights up.
T1
3) Rotating the ENCODER knob - A (E1) until obtaining on the
PARAMETER DISPLAY screen - A (D1) and the writing MiG .
E1
D1
2 - SELECTION OF WELDING PROGRAMME
PROGRAM TABLE (*)
MIG-MAG PROCESS
PROGRAM
NUMBER
MATERIAL
WIRE Ø
(mm)
GAS DISPLAYS
TYPE CLASS
000 Fe G3 Si-1 0.6 CO
2
MiG 000
001 Fe G3 Si-1 0.8 CO
2
MiG 001
002 Fe G3 Si-1 1.0 CO
2
MiG 002
010 Fe G3 Si-1 0.6 Ar/16-20%CO
2
MiG 010
011 Fe G3 Si-1 0.8 Ar/16-20%CO
2
MiG 011
012 Fe G3 Si-1 1.0 Ar/16-20%CO
2
MiG 012
015 Fe G3 Si-1 0.9 Ar/16-20%CO
2
MiG 015
195 Fe-rutil flux-cored E71T-GS 0.9 (**) MiG 195
231 CrNi 308 G 19 9 LSI 0.8 Ar/2-3%CO
2
MiG 231
232 CrNi 308 G 19 9 LSI 1.0 Ar/2-3%CO
2
MiG 232
402 Al 99.9 S Al 1050 1.0 Ar MiG 402
412 Al Mg 5 S Al 5356 1.0 Ar MiG 412
422 Al Si 5 S Al 4043A 1.0 Ar MiG 422
511 Cu Si 3 S CuSi3 0.8 Ar MiG 511
512 Cu Si 3 S CuSi3 1.0 Ar MiG 512
(*) THE programmes of welding can be updated and broadened. Re-
fer to the table on the welder to have the correct list of the available
programmes.
(**) When one utilises this wire, remember to mechanically invert the
poles (see section “MIG-MAG welding without GAS” on the manual.
Select the PROGRAM of synergic MIG-MAG welding by pressing
and releasing, even several times if necessary, the PROGRAM
SELECTION key (T1) until the corresponding LED is lit and after
that rotating the ENCODER knob - V (E2) until obtaining on the
PARAMETER DISPLAY screen - V (D2) the number of the pro-
gramme desired.
E2
T1
D2
3 - WELDING MODE SELECTION
Select the MODE of welding, pressing and releasing, even various
times if necessary, the WELDING MODE SELECTION key (T3)
until the corresponding LED lights up.
1 6 2 4 3 5
T3
1. TWO STROKE (2T)
2. FOUR STROKE (4T)
3. CRATER 2T
4. CRATER 4T
5. SPOT WELDING 2T
6. STITCH WELDING 2T