CEA TREO 1800 Synergic MIG-MAG Скачать руководство пользователя страница 30

Страница: 30 / 42

SAFETY CALIBRATION CODE (SCC)

ATTENTION:

This operation, if carryed on, optimizes the effi-

ciency of the welding circuit (only in MIG welding processes).

To set the length of the welding circuit (adjustable from 1 to 100

m) follow this procedure:

• Within the SECOND LEVEL MENU, rotate the ENCODER knob

- A (E1) until obtaining on the PARAMETER DISPLAY screen -

A (D1) and the writing

SCC

• Rotate the ENCODER knob - V (E2) until obtaining on the PA-

RAMETER DISPLAY screen - V (D2) the desired number.

CAUTION:

The operation does not require confirmation!

CAUTION:

The data inserted is valid for all the MIG welding pro-

cesses.

Example:

Length of cable mass 3 m.

Length of welding torch cable 3 m.

The overall length of the welding circuit is 6 m (6 is the number that

will therefore be inserted).

MOTOR CALIBRATION (CAL)

ATTENTION:

This procedure allows you to calibrate the wire

speed (only in MIG welding processes).

Proceed as follows:

• Within the SECOND LEVEL MENU rotate the ENCODER - A

(E1) knob until the PARAMETER DISPLAY - A (D1) screen re-

ads

CAL

• To access the CALIBRATION MENU hold the SAVE “MEM” key

(T2) down for at least

consecutive seconds.

• The procedure of calibration is carried out in 3 different phases:

Calibration parameter SM1 (MINIMUM SPEED)

Press and release the torch button, then wait for the auto-

matic arrest of the wire. Measure (in cm) the dangling wire

and insert the value shown, in the software of the welder,

by means of the rotation of the ENCODER knob - V (E2)

appearing on the PARAMETER DISPLAY screen - V (D2)

is the desired value.

Calibration parameter SM2 (MEDIUM SPEED)

Then turn the ENCODER - A knob (E1) until the PARAME-

TER DISPLAY - A screen (D1) shows the

SM2

parameter.

Press and release the torch button, then wait for the auto-

matic arrest of the wire. Measure (in cm) the dangling wire

and insert the value shown, in the software of the welder,

by means of the rotation of the ENCODER knob - V (E2)

appearing on the PARAMETER DISPLAY screen - V (D2)

is the desired value.

Calibration parameter SM3 (MAXIMUM SPEED)

Then turn the ENCODER - A knob (E1) until the PARAME-

TER DISPLAY - A screen (D1) shows the

SM3

parameter.

Press and release the torch button, then wait for the auto-

matic arrest of the wire. Measure (in cm) the dangling wire

and insert the value shown, in the software of the welder,

by means of the rotation of the ENCODER knob - V (E2)

appearing on the PARAMETER DISPLAY screen - V (D2)

is the desired value.

Содержание TREO 1800 Synergic MIG-MAG











































Результаты поиска

Содержание TREO 1800 Synergic MIG-MAG

Отзывы:

Бренды по названию

Популярные бренды

CEA TREO 1800 Synergic MIG-MAG, Руководство оператора

Результаты поиска

Содержание TREO 1800 Synergic MIG-MAG

Отзывы:

Бренды по названию

Популярные бренды