CDVI DIGIWAY PLUS, Руководство пользователя

Страница: 30 / 48

EN EN
DIGIWAY Plus
Inward or Outward Door Operator
30
Remote controls management Remote controls management
The unit is equipped with a superhetherodyne AM receiver with The unit is equipped with a superhetherodyne AM receiver with Keeloq® Hopping code Keeloq® Hopping code
security protocol. security protocol.
In the TX Management menu you can manage the memory of the receiver, which can In the TX Management menu you can manage the memory of the receiver, which can
store up to 50 transmitters. store up to 50 transmitters.
MENU MAIN
Tx Management
Tx Management
ADD
Press TX Button
to ADD
Press TX Button
to REMOVE
Tx Management
REMOVE
Tx Management
REMOVE ALL
REMOVE ALL TX
from DATABASE?
To add a transmitter to the memory, select ADD from the TX To add a transmitter to the memory, select ADD from the TX
MANAGEMENT menu and press OK. At the message “PRESS MANAGEMENT menu and press OK. At the message “PRESS
TX BUTTON to ADD”, press the button of the transmitter to TX BUTTON to ADD”, press the button of the transmitter to
memorize it . If everything is correct memorize it . If everything is correct the the Serial Number of the Serial Number of the
transmitter will appear on the LCD display. If the transmitter transmitter will appear on the LCD display. If the transmitter
is already present in the memory, is already present in the memory, the following message will the following message will
appear appear: TX ALREADY PRESENT. : TX ALREADY PRESENT.
To delete a transmitter select the option To delete a transmitter select the option REMOVE REMOVE from from
the menu the menu TX MANAGEMENT and press OK. TX MANAGEMENT and press OK. At the message At the message
“PRESS TX BUTTON to “PRESS TX BUTTON to REMOVE, REMOVE, press the button of the press the button of the
transmitter to transmitter to delete. delete. If everything is correct, the If everything is correct, the message message: :
TX REMOVED TX REMOVED will appear will appear on the LCD display. on the LCD display.
To delete the first transmitter it’s enough to press one button. To delete the first transmitter it’s enough to press one button.
To delete any other transmitter you need to delete each To delete any other transmitter you need to delete each
button individually. button individually.
To erase completely the database select the option To erase completely the database select the option REMOVE REMOVE
ALL ALL from the menu TX MANAGEMENT and confirm. from the menu TX MANAGEMENT and confirm. At the At the
message message “REMOVE ALL TX from DATABASE, press OK and “REMOVE ALL TX from DATABASE, press OK and
the memory will be completely erased. the memory will be completely erased.
ATTENTION: ATTENTION: This action also removes the 4-ch transmitter, This action also removes the 4-ch transmitter,
used to navigate through the menu. Navigation will only be used to navigate through the menu. Navigation will only be
possible with the keyboard buttons or after memorization of possible with the keyboard buttons or after memorization of
a new 4-ch transmitter, in the first memory location. a new 4-ch transmitter, in the first memory location.
Menu Service Menu Service
The unit is equipped with 2 cycle counters: The unit is equipped with 2 cycle counters: Absolute Counter Absolute Counter and and Partial Counter Partial Counter
The The Absolute Counter Absolute Counter registers the cycles of the motor for all its life: It cannot be registers the cycles of the motor for all its life: It cannot be
reset except by the factory. The counter increments by 1 if the door makes a clean reset except by the factory. The counter increments by 1 if the door makes a clean
cycle of pause+closing without any obstacle or re-opening action caused by a cycle of pause+closing without any obstacle or re-opening action caused by a
sensor (radar, photocells, etc). The current value of the absolute counter can be seen sensor (radar, photocells, etc). The current value of the absolute counter can be seen
on the INFORMATION menu (see next page). on the INFORMATION menu (see next page).
The The Partial Counter Partial Counter can be used to set a maintenance period. It can be reset after a can be used to set a maintenance period. It can be reset after a
service intervention. service intervention.