CCTV SYSTEM
12
6
、
Product connection
Figure (20)
Step C. Set driver of dome:
refer to the drive setting of wall-
hung dome on Page 10
Step D. Install the module
: refer to the installation of wall-
hung dome module on Page 10
Step E. Install the lower housing
: refer to the installation of
lower housing of wallhung dome on Page 10
figure
（
19
）
5
、
Lifting installation of dome:
figure
（
17
）
Step b Install dome camera
⑴
Put the video lines, power lines and signal-control lines
through the hollow tube of hanger rod, and fasten the dome
and the hanger rod.
⑵
Put the video lines, power lines and signal-control lines
through the central holes at the hanger bottom and into the
sealing groove at the side notch of the bottom of connecting
base of the hanger, ad fasten the dome and the hanger rod as
figure 18 shows
⑶
Fix the installed dome camera onto the ceiling.
Note: If dome is used outdoor, seal the joint face
between the ceiling and the hanger base, and around
the holes with silica gel to be waterproof. Tape around
the screws at the top of hanger rod and fasten the
hanger to the hanger bottom. As figure 19 shows,,
seal the joint face between hanger joint sleeve and the
hanger with silica gel to be waterproof.
figure
（
18
）
Step a Drill holes on the ceiling
(1) Take the holes of the ceiling base as a template and mark the
positions of the holes as figure 17 shows. Drill the holes and
load with bulgy screws inside.
12V
IR Intelligent Speed Dome Operation Manual ver2.0
33
1. Dome function Express
Preset NO.
Speed dome / camera control content
Call preset
Set preset
110
Set the left limit
¤
111
Set the right limit
¤
112
Start the limit scan
¤
112
Save the limit scan
¤
110
Set the left and right limit scanning speed :
[call No.110 call preset N,N for 1-100
(representing the speed grade) the default of 10 de-
grees per second]
¤
115
Start the second programmed tour1-16 scanning
¤
116
Start the first programmed tour
17-32 scanning
¤
117
Start the second programmed tour33-48 scanning
¤
118
Start the third programmed tour
49-64scanning
¤
119
Start the fourth programmed tour
65-80scanning
¤
115
The speed of tour [set preset 115+set preset point N,N
for 1-100(N representing the speed grade)
¤
116
The time of tour [set preset 116+set preset point N,N
for 1-250(N representing the time)
¤
120
Start the level 360
°
automatic clockwise scan
¤
121
Start the level 360
°
automatic counterclockwise scan
¤
122
Start the level 360
°
automatic reciprocating scan
¤
120
Set the speed of automatic tour:[ set preset 120+preset
point N,N for 1-100( N representing the speed grade)
the default of 10 degrees per second]
¤
124
Free movement on
¤
124
Free movement off
¤
125
Set the left and right limit scanning speed :[call
No.100call preset N,N for 1-100(representing
the speed grade) the default of 10 degrees per second)]
¤
125
Idle operation start time setting:[set No.125 set
the preset point N,N for 1-250(N represents time )
¤
126
Boot action settings:[set No.126 calling the
corresponding instruction table in the preset number
( preset number must be corresponding functional)]
¤
130
Start the scan
¤
131
Start the second scan (effective for menu camera )
132
Start the third scan (effective for menu camera )
133
Start the forth scan (effective for menu camera )
134
Set the scan pattern 1:( calls the preset point 134 to
start recording pattern scan, according to the require-
ments of users of mobile lens, and call presets 134
again ,the dome automatic save and exit) call 130 to
start
¤
