CBE 510 Скачать руководство пользователя страница 12

Страница: 12 / 60

RECEIPT AND INSPECTION

After uncrating the packer, a check should be made to see that all items ordered have been received and that
all equipment is in good condition.

Any damage incurred in shipment should be reported immediately to the delivering carrier and a claim for the
damage should be filed. Also notify Choice Bagging Equipment, Ltd. so that replacement or repair may be
initiated.

If severe damage has occurred, verify the damage with written reports AND pictures to

Choice Bagging Equipment and call the trucking company or transportation provide.

1. Determine location of all switches.

2. Be sure all guards are in place and observe all warning signs.

3. Check and maintain all oil levels with proper specific oil ( if equipped).

4. Be sure all electrical equipment is free of any accumulation of water before installing.

CAUTION AND WARNINGS

1. Observe extreme caution when switches are turned on. Operation may start automatically

after a time delay.

DO NOT

open junction boxes or control panels unless you are a qualified technician. Be sure

POWER IS OFF

. Except when electricians are performing maintenance, electrical enclosures

and junction boxes should

REMAIN SECURELY CLOSED

STOP

machine and disconnect power supply before servicing or repairing. Maintenance and

adjustments must be performed with all electrical power supplies disconnected unless
otherwise specified in this manual.

READ COMPLETELY

any information associated with this bulk bagger. There is

additional manual included for the GSE controller.

DO NOT

attempt to defeat any safety switches. Serious injury could result. (If applicable)

6. While machine control power is ON, do not activate limit switches manually. Serious injury

and/or machine damage could result. Disable machine before attempting any maintenance or
manual testing of components. (If applicable)

7. If additional wire runs are added to any junction box or control panel, wiring practice should be

such as to maintain prevailing electrical hazard classification.

Содержание 510





























































Результаты поиска

Содержание 510

Отзывы:

Бренды по названию

Популярные бренды

CBE 510, Безопасность, Установка, Эксплуатация, Обслуживание

Результаты поиска

Содержание 510

Отзывы:

Бренды по названию

Популярные бренды