background image

 

13

CB Svendsen A/S                                                    

 

 

 

 

Installation guide for FA-20:

 

 
For correct installation of a FA-20 Remote Reading Unit you must follow this installation guide 
carefully: 

 
1. Insertion of SIM-card into FA-20. 

 
Use a SIM-card that supports data V.110 + SMS and disable the PIN/PUK code in advance 
by means of a mobile phone.  
 
The FA-20´s GSM modem is placed to the left of the plastic column in the middle of the case. 
The SIM-card reader is placed on top of the GSM modem. The SIM-card reader is divided into 
two  (lid  and  bottom)  and  hinged  at  the  “top””.  You  push  the  “lid”  up  towards  the 
pushbutton/the antenna plug, after which the lid can be opened to 90 degrees (or more). The 
SIM-card  can  hereafter  be  pushed  into  the  slit  on  the  lid  with  the SIM-cards  beveled  corner 
upwards to the right. Then the lid is closed and the SIM-card is pushed into to lid just enough 
so that the lid can be closed in the bottom. Then the lid is pulled downwards until it locks. 

 

 
2. The physical location of FA-20: 

 
Typically  FA-20  is  placed  next  to  one  of  the  meters  that  are  to  be  logged.  The  most 
convenient location is against a wall, vertically and e.g. 1.6 meters over the floor. This location 
secures  a  convenient  working  position  for  the  user  when  pressing  the  pushbutton  and 
observing the two signal lamps.  

 
3. Wall-mounting of FA-20. 

 
FA-20 is specifically designed for wall mounting using 3 self-cutting screws (BN615: 3.5x30) 
and raw plugs (HFC365: Ø6). When applying raw plugs please note: 
 
Place  the  FA-20  unit  with  the  cover  detached  against  the  wall  and  mark  the  precise  drilling 
position on the wall.  Drill holes (ø6, 40 mm deep) and attach the unit to the wall. 

 
 
4. Installation of pulse-inputs. 

 
FA-20  features  2  pulse-inputs  used  to  receive  pulse  signals  from  the  potential-free  contact 
(relay) S01 or from the optocoupler. The cable should have an outside diameter of 4.5 mm ± 
0.5 mm in order to secure maximum of pull relief.  
 
Terminals for the 2 pulse inputs are  
1+2 and 3+4. 

 

 
 

 
 

Specifications are subject to revision without notice

 

Содержание FA-20



























Отзывы: