Carrier 80AWH-065 series, Инструкции по установке, эксплуатации и обслуживанию

Страница: 29 / 124

29
English
5.7 - Power Wiring Diagram
Refer to the Safety Information Manual and to the
electrical scheme supplied with the unit.
Electrical installation must be according to fig. 16 .
Description
80AW-065 80AW-115 80AW-150
M0 M3 M6 T6 M0 M3 M6 T6 T9 M0 T6 T9
A Power supply - 1pH - 230V
3Ph+N –
400V
- 1pH - 230V 3Ph+N – 400V - 3Ph+N – 400V
B
Electrical heat er breaker (field supplied)
-
2 poles
20 A
2 poles
32 A
4 poles
16 A
-
2 poles
20 A
2 poles
32 A
4 poles
16 A
4 poles
20 A
-
4 poles
16 A
4 poles
20 A
C Outdoor unit breaker (field supplied) 2 poles, 16 A 2 poles, 25 A 4 poles, 25 A
D Booster heater breaker (field supplied)* 2 poles, 16 A 2 poles, 16 A 2 poles, 16 A
Description
Cable
Type
80AW-065 80AW-115 80AW-150
M0 M3 M6 T6 M0 M3 M6 T6 T9 M0 T6 T9
1 Outdoor unit power supply cable H07 RN-F 3G x 2.5 mm
2
3G x 4 mm
2
5G x 2.5 mm
2
2 Indoor unit power supply and
communication cable
H07 RN-F 3G x 1 mm
2
3G x 1 mm
2
3G x 1 mm
2
3
Backup heater power supply cable
H07 RN-F -
3G x 4
mm
2
3G x 6
mm
2
5 x 4
mm
2
(L1, L2,
L3, N,
Y/G)
-
3G x 4
mm
2
3G x 6
mm
2
5 x 4
mm
2
(L1, L2,
L3, N,
Y/G)
5 x 6
mm
2
(L1, L2,
L3, N,
Y/G)
5 x 4
mm
2
(L1, L2,
L3, N,
Y/G)
5 x 6
mm
2
(L1, L2,
L3, N,
Y/G)
4 User interface cable FROH2R 4 x 0.75 mm
2
4 x 0.75 mm
2
4 x 0.75 mm
2
5 Booster heater power supply cable* H05VV-F 3G x 2.5 mm
2
3G x 2.5 mm
2
3G x 2.5 mm
2
6 Booster heater activation cable* FROH2R 2 x 1 mm
2
2 x 1 mm
2
2 x 1 mm
2
7 Sanitary hot water sensor cable FROH2R 2 x 0.5 mm
2
2 x 0.5 mm
2
2 x 0.5 mm
2
8 Remote outdoor sensor cable FROH2R 2 x 0.5 mm
2
2 x 0.5 mm
2
2 x 0.5 mm
2
* Valid for domestic hot water tanks listed in paragraph
Accessories.
If the user interface is installed in zone, install it in a place
which represents ambient room temperature. Avoid direct
contact or proximity with heat or cool sources.
Appropriate installation height is 1.5 m from the ground.
See electrical scheme for more information.
5.8 - Wiring Connection Diagram
• Units without backup heater, see fig. 17 .
• Units with backup heater, single phase power supply,
see fig. 18 and fig. 20a .
• Units with backup heater, tri-phase power supply, see
fig. 19 and fig. 20c .
• Connection between Indoor and Outdoor units: see
fig. 20b .
5.8.1 - Terminal block description
See fig. 17,18,19 .
Terminal
Block
Description Details
1 - 2 - 3 Indoor unit power supply and
communication cable
4 - 5 Pump cut off contact (EN1264-4)*
6 - N Booster heater control* (domestic hot
water tank)
Output, 230 V, max 2 A
(inductive)
7 - 8 - N Domestic hot water 3 way valve* Output, 230 V, max 2 A
(inductive)
10 - 11 Domestic hot water tank sensor* Input, Analog
12 - 15 Hi energy rate input Input, Dry Contact
13 - N Multi-purpose output Output, 230 V, max 2 A
(inductive)
14 - 15 System ON/OFF input Input, Dry Contact
15 Common for dry contact input Input, Dry Contact
W-C-G-Y User interface placed on the unit or
removed from the unit and mounted
in zone
20 - 15 Heat/Cool thermostat input Input, Dry Contact
21 - 15 Heat/Cool selection input Input, Dry Contact
22 - 15 Domestic hot water input Input, Dry Contact
Rc-Rh-G2-Y2 Additional user interface or 2 zone kit
connection
N Neutral
31 - N Boiler (only for units 80AW---M0) Output, 230 V, max 2 A
(inductive)
* See paragraph
Accessories
.