Carrier 62X 03 Series Скачать руководство пользователя страница 109

Страница: 109 / 114

CL-9

START-UP CHECKLIST

Copy to be provided to the customer and sales office.

Prior to performing start-up, the crank case heaters must operate for 24 hours.

Cooling start-up can only be performed when the outdoor air temperature is above 55°F

An Equipment Touch, Equipment Touch App, or Field Assistant is required to perform startup

PROJECT INFORMATION

Project Name______________________________________

Address _________________________________________

City______________________________________________

State/Providence_______________ Zip Code ____________

Installer __________________________________________
Contact Name_____________________________________

Contact Phone_____________________________________

Contact Email______________________________________

UNIT INFORMATION

Model Number_____________________________________

Serial Number _____________________________________

INSTRUCTIONS

Check the box to verify the activity is completed. If the activity does not apply, write N/A in the box.

PRE-STARTUP CHECKLIST

Installation



All packing materials have been removed from the unit.



The unit is free of damage. If damage exists, contact your local Carrier representative.



The unit has been installed in accordance with required service clearances and required access.



The unit is within level tolerances to promote proper condensate drainage.



All required field installed unit components (hoods, filters, sensors, etc.) have been installed.



Space cooling and heating units exist to control space conditions (temperature and humidity).

Electrical



The unit power feed is installed.



The unit voltage and frequency have been verified to match the incoming power and phasing.



The power feed phasing is correct.



The power feed meets the MCA requirements as indicated on the unit label.



The fuses or circuit breaker safeties meet the MOCP requirements as indicated on the unit label.



All electrical connections and terminals are tight; all terminals are free from corrosion.



Measure the voltage between each power feed and record the measured voltage on the startup log.



The power voltage is within 10% of nameplate voltage and the voltage imbalance is less than +/-2%

Supply Fan



The outdoor air damper is closed



The supply fan(s) are free from obstruction and rotate properly



The outdoor air screens are installed and are clean



The evaporator filters are installed and are clean



All fire dampers or VAV dampers are open to allow free airflow

Cooling



The air-cooled condenser coil(s) is clean and free from obstructions and defects



The evaporator coils are clean and free from obstructions and defects



The refrigeration circuit is free from leaks and contains a refrigerant charge



The scroll compressors are rotating in the correct direction and the compressor oil level is acceptable



The condenser fan(s) rotation direction is correct, and rotation is not obstructed



The condensate drain trap has been installed per installation instructions and is draining freely



The crank case heaters verified to be operational and will operate 24 hours prior to cooling start-up

WARNING: To avoid injury to personnel and damage to equipment or property when completing

the procedures listed in this start-up checklist, use good judgment, follow safe practices, and

adhere to the safety considerations/information as outlined in preceding sections of this Controls,

Operation, and Troubleshooting guide.

Содержание 62X 03 Series



















































































































Результаты поиска

Содержание 62X 03 Series

Отзывы:

Похожие инструкции для 62X 03 Series

Бренды по названию

Популярные бренды

Carrier 62X 03 Series, Стартап

Результаты поиска

Содержание 62X 03 Series

Отзывы:

Похожие инструкции для 62X 03 Series

Бренды по названию

Популярные бренды