caron 6010 Скачать руководство пользователя страница 29

Страница: 29 / 35

TROUBLESHOOTING

GUIDE

PROBLEM:

No power, main power switch light not energized

POSSIBLE CAUSES:

1.  Power lines not wired properly into grounded wall outlet
2.  Main fuse blown
3.  Customer power defective

PROBLEM:

Cabinet not heating, safeties not energized

POSSIBLE CAUSES:

1.  Heater fuse blown
2.  Snap disc open
3.  Thermal fuse open
4.  Main temperature control and/or sensor defective
5.  Controller not programmed properly
6.  Poor air circulation within the chamber
7.  Solid State Relay Defective

PROBLEM:

Cabinet not cooling, over-temp safety energized

POSSIBLE CAUSES:

1.  Compressor switch is not on
2.  Compressor is hot, trip out on thermal overload
3.  Poor internal air circulation
4.  Heat is remaining on

PROBLEM:

Inconsistent temperature control and then over-temp safety energizes

POSSIBLE CAUSES:

1.  Circulation fan defective
2.  Temperature sensors out of position or defective
3.  Controller not programmed properly

For further troubleshooting procedures, refer to the individual manuals for the controllers,
recorder, or contact CARON at

740-373-6809

Содержание 6010




































Результаты поиска

Содержание 6010

Отзывы:

Похожие инструкции для 6010

Бренды по названию

Популярные бренды

caron 6010, Руководство по эксплуатации

Результаты поиска

Содержание 6010

Отзывы:

Похожие инструкции для 6010

Бренды по названию

Популярные бренды