caron 6010 Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 35

background image

Humidity (Chromalox) Controller Calibration (for Watlow controllers, see Appendix A)

1. Remove the access panel (control panel cover 6030), (right side panel 6010).
2. Find the 2” x 3” black utility box located adjacent to the wiring and in the service area.

(Behind fuse panel 6030, near ceiling 6010).

3. Inside the utility box is the humidity module.
4. Slowly adjust the BOTTOM humidity calibration pot to the desired calibration point as shown

on the humidity controller readout.

Humidity Water Inlet

Model

6030:

Facing the back is a water connection in the upper right hand corner. The ¼” FPT

fitting is attached to a filter/strainer and pressure regulator that is set at 40 PSI. Any type of ¼

MPT fitting can be used to connect to water supply.

Model

6010:

Facing the back is a water connection in the lower right hand corner. The ¼ FPT

fitting is attached to a filter/strainer and pressure regulator that is set at 40 PSI. Any type of ¼
MPT fitting can be used to connect to water supply.

«
...
12
13
14
15
16
...
»

Содержание 6010




































Отзывы:

Нет отзывов

Похожие инструкции для 6010

Бренд: OMCA Страницы: 72

Бренд: Barko Hydraulics Страницы: 92

Бренд: ACDC Страницы: 4

Бренд: Rapid Technic Страницы: 152

Бренд: Quincy Страницы: 31

Lyme FIA Sofia 2

Бренд: Quidel Страницы: 49

Бренд: Quest Leisure Products Страницы: 12

Бренд: Tactile Medical Страницы: 23

Бренд: Taarup Страницы: 72

PRO-FORM ab GLIDER

Бренд: ICON Health & Fitness Страницы: 16

Biosafe 110 Port

Бренд: Sartorius Страницы: 2

Aqua Timer 3000

Бренд: Melnor Страницы: 6

Бренд: KUHN Страницы: 112

Бренд: Federal Signal Corporation Страницы: 31

TEMSTM POCKET 7.3

Бренд: ASCOM Страницы: 8

Бренд: Chamberlain Страницы: 8

Бренд: LINET Страницы: 25

Бренд: MD SPORTS Страницы: 12

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды