caron 6010 Скачать руководство пользователя страница 7 | Manualshive

Страница: 7 / 35

background image

INSTALLATION

Unpacking

This product has been completely tested, cleaned and packed for shipment. Carefully remove all

packing material. Please examine the chamber completely. Should any damage be found, notify

the delivering carrier immediately.
Report any shortages to Customer Service at

1-740-373-6809

.

Chamber Location

Chamber ambient conditions 20

°

C to 25

°

C. Exceeding 25

°

C can result in chamber failure.

The chamber must be located in a dry, clean, and level area.  Allow a 4” clearance from the back
and top of the chamber for proper air circulation and ease of installation.  Locate the chamber in
an area out of direct sunlight and away from heating and cooling ducts. The 6010 & 6030
chambers can exhaust 2500 BTU/hr (730 W) and 4000 BTU/hr (1170 W) respectively into the
surroundings.  The figure below shows a side view of the chamber with air vent and access port
locations.
Models

6030,

6031,

603

2

: Tilt the unit ½ of a level’s bubble toward the back for proper water

drainage
Models

6010,

6011,

6012:

Unit should be completely level for proper water drainage

«
...
5
6
7
8
9
...
»

Содержание 6010




































Отзывы:

Нет отзывов

Похожие инструкции для 6010

Бренд: Ecco Страницы: 2

Бренд: Landoll Страницы: 94

Бренд: RASHA PROFESSIONAL Страницы: 11

Бренд: MADRIX Страницы: 24

Бренд: MADRIX Страницы: 28

Бренд: GE Страницы: 37

Бренд: Yacht Devices Страницы: 68

WELCH LVS 600 T

Бренд: Gardner Denver Страницы: 68

Бренд: Warner Electric Страницы: 14

Бренд: Major tech Страницы: 12

XMLT-24ELED-200CA8-1

Бренд: DS Produkte Страницы: 28

Бренд: Mindray Страницы: 295

Бренд: ZAMST Страницы: 14

Бренд: Pixlip Страницы: 15

Бренд: AGI Страницы: 33

LIGHT LINEAR PT 1

Бренд: LIGMAN Страницы: 6

Бренд: QRS Страницы: 12

Бренд: Ikan Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды