Caroma Invisi Series II Скачать руководство пользователя

Страница: 14 / 16

INVISI

™

SERIES II

Servicing - Outlet Valve

Wash seal to remove any dirt and inspect

for damage. If necessary remove seal

and replace (Spare Part Kit 237 070).

237 070S

Ensure water is turned off and

remove Outlet Valve from tank as

per the instructions on page 13.

Re-assemble complete Outlet Valve and

refit into tank. Turn water back on, wait for

tank to fill and test both buttons to ensure

they activate the outlet valve.

Seal

• Servicing is only required in instances where outlet valve operation is found to be faulty.

Servicing Requirements

• If Outlet Valve leaks ► Inspect seal for damage and replace if necessary.

• If short flushing ► Check pneumatic tubes are pushed into the bridge and buttons

• If any other issues arise ► Consult a plumber or Caroma After Sales Service.

Troubleshooting Guide

• Caroma Invisi II Outlet Valve compatible Spare Part Kits are:

237 072

Containing -

1 x Complete 4.8/3L Replacement Outlet Valve

237 070

Containing -

Diaphragm Seal

(10 Pack)

237 070S

for Single Diaphram Seal

Refer to

Maintenance & Spare Parts Instructions

Spare Parts Information

Maintenance & Spare Parts Instructions

Содержание Invisi Series II

















Результаты поиска

Содержание Invisi Series II

Отзывы:

Похожие инструкции для Invisi Series II

Бренды по названию

Популярные бренды

Caroma Invisi Series II, Руководство пользователя

Результаты поиска

Содержание Invisi Series II

Отзывы:

Похожие инструкции для Invisi Series II

Бренды по названию

Популярные бренды