manualshive.com logo in svg

Carlton SP8018, Руководство пользователя, Страница: 83 / 96

Поделиться
Скачать
Carlton SP8018 Скачать руководство пользователя страница 83

13 

 

 

2.4.4 

Refitting the Belt  

 

1.  Support the machine safely off the ground, fit the new belt over the idler end first.  

2.  With the idler fully retracted fit the belt over the sprocket. This may require the use of a 
prybar to walk the belt into place. 

 

3.  Ensure the sprocket is meshed properly and the belt is seated correctly on the rollers.  

4.  Tighten the valve and slowly apply grease. The Idler will gradually move out to its working 
position.  

5.  Set to the correct tension using the test methods mentioned in section (2.3)  

 

6.  Clean off any loose grease and refit tensioner cover plate.  

7.  Lower the machine back to the floor and check the machine by briefly tracking in each 
direction checking for belt slip/ de-tracking.  

8.  If not tensioned correctly, repeat step 5.  

 

 

 

WARNING 

The above procedure involves heavy components, use appropriate lifting equipment 
to prevent injury to operators and bystanders. 

! 

Содержание SP8018

































































































Отзывы:

Нет отзывов