manualshive.com logo in svg

Carlton SP8018, Руководство пользователя, Страница: 81 / 96

Поделиться
Скачать
Carlton SP8018 Скачать руководство пользователя страница 81

11 

 

 

2.4.1 

Tightening the Track 

 

 

• 

 Loosen one of the two screws and swing access cover away from access aperture on 

the side of the track frame (if applicable).  

• 

 Ensure the grease fitting and grease gun adaptor is clean; ingress of dirt into the 

grease fitting can result in failure. Connect a grease gun to the grease fitting and add 
grease until the track tension is within the specified values given in Section 2.3.  

• 

 Drive 50 yards forwards and 50 yards backwards and repeat the above procedure if 

the track slackens.  

 

2.4.2 

Slackening the Track  

 

• 

 Loosen one of the two screws and swing access cover away from access aperture on 

the side of the track frame (if applicable).  

• 

 Loosen the grease fitting, by turning in a counterclockwise direction, using gradual 

increments until the grease begins to be expelled. Care must be taken not to loosen 
the grease fitting too quickly.  

• 

 When the correct track tension has been obtained, tighten the grease fitting by 

turning in a clockwise direction and clean away all trace of extruded grease. Be sure 
not to over tighten the grease fitting.  

 

If the track fails to slacken after grease fitting has been loosened; 

DO NOT 

attempt to remove 

the tracks or disassemble the track tensioner, and 

DO NOT 

remove the grease fitting from the 

tensioner. It is possible that running the tracks a short distance in both directions with the 
grease fitting loosened may help to expel the grease. 

 

 

 

WARNING 

The above procedure involves working with grease contained at high pressure and 
must only be carried out by qualified fitters. 

! 

Содержание SP8018

































































































Отзывы:

Нет отзывов