Carlton SP8018 Скачать руководство пользователя страница 36 | Manualshive

Страница: 36 / 96

Carlton SP8018 Скачать руководство пользователя страница 36

SP8018 MACHINE MAINTENANCE

*PLACE THE CUTTER WHEEL ON THE GROUND WHEN PERFORMING SERVICE

ENGINE

The air filters, the radiator screens and fans, the oil and fuel filters are all extremely important for
machine operation!

Refer to the engine manufacturer’s manual for detailed guidelines on

maintaining these and other engine components.

AIR FILTERS

–

PRIMARY & SAFETY

•

Inspect the primary and safety air filters
(

Daily

).

•

Do not tap or hit the primary air filter to
clean it. Do not wash the primary air
filter. Follow the engine manual for
cleaning the primary air filter. Replace
the air filter when it cannot be cleaned or
after cleaning six times or if damaged.

•

Do not clean the safety filter. Replace the
safety filter if dirty or when the main air
filter has been

cleaned

3 times.

IMPORTANT:

Remove secondary (safety)

element ONLY for replacement. DO NOT
attempt to clean, wash, or reuse secondary
element.

•

When cleaning or changing the air filters,
place tape over the air inlet hole to reduce
the chance of any dirt getting inside the
engine. Use a clean dry cloth to wipe down
the inside of the air cleaner housing and
cover.

•

Check the general condition of the air
cleaner housing and components. Make
sure there are no dents, cracks, or other
damage to these parts that could allow
unfiltered air to enter the engine.

DANGER

More accidents occur while performing maintenance than any other time! Use extra caution!!

DO NOT PERFORM MAINTENANCE OF ANY KIND ON THIS MACHINE UNLESS:



The engine is turned off.



The ignition key has been removed.



The positive battery cable has been disconnected.



The cutter wheel is disengaged.



All machine parts have come to a complete stop.



All machine parts have had sufficient time to cool down.



No operator is in position at the controls to accidentally start machine.



At least 2 people are at the site where maintenance is performed.

NOTICE

Never run the engine without the air filter
installed or with a damaged air filter. Replace
air filters if there is damage to the pleats,
gaskets, or seals. The air filter is used to
prevent airborne debris from entering the
engine. If dirt is allowed to get into the engine
it will greatly reduce engine life and/or cause
damage. Never service the air cleaner with the
engine running.

!

SAFETY FILTER

PRIMARY FILTER

DUST CAP/COVER

23

«
...
34
35
36
37
38
...
»

Содержание SP8018

































































































Отзывы:

Нет отзывов