Carlton 3500D Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 129

Carlton 3500D Скачать руководство пользователя страница 47

3500D MACHINE MAINTENANCE

25

•

Grease cutter wheel shaft bearings daily.
These bearings should be purged using
grease

EVERYDAY

.

Purge until clean

grease is seen.

Use Texaco

®

Starplex II

grease. Wipe off excess grease.

Excess

grease will attract dirt. Always clean tip
of grease gun fitting and grease fitting on
machine before attaching hose to prevent
dirt from being forced into machine
parts.

•

Grease the bearing supported stub shaft
every 1000 hours of operation using
Texaco

®

Starplex II grease. The grease

fitting is easily accessible behind the V-belt
guard. Apply grease using a hand held
grease gun until the pin extends from the
pressure relief valve (located 180

°

from

grease fitting on the bearing). Wipe off
excess grease.

Excess grease will attract

dirt.

•

A grease fitting is on the end of the stub
shaft to grease the spline coupling. Apply 2
to 3 shots of grease approximately every
1000 hours of operation. Wipe off excess
grease.

Excess grease will attract dirt.

DO NOT

over grease, over greasing could

cause a hydraulic type lift on seals

.

GREASE APPROXIMATELY EVERY

1000 HOURS OF OPERATION

PIN

«
...
45
46
47
48
49
...
»

Содержание 3500D


































































































































Отзывы:

Нет отзывов