Carlton 3500D Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 129

Carlton 3500D Скачать руководство пользователя страница 46

3500D MACHINE MAINTENANCE

24

•

Check cutter wheel, pockets, and teeth for
wear. If any repair is needed, see Servicing
Cutter wheel section for further instructions.

DO NOT OPERATE STUMP CUTTER
WITHOUT A COMPLETE SET OF
TEETH.

Always clean tip of grease gun fitting and grease fitting on machine before attaching hose
to prevent dirt from being forced into machine parts.

•

Grease engine slide assembly daily. Use
Texaco

®

Starplex II grease. Wipe off

excess grease.

Excess grease will attract

dirt.

•

Grease engagement arm pivot weekly, 2
places. Use Texaco

®

Starplex II grease.

Wipe off excess grease.

Excess grease will

attract dirt.

•

Grease jackshaft bearings daily. There is a
cover on the jackshaft bearings with slots to
access the grease fittings. These bearings
should be purged using grease

EVERYDAY

.

Purge until clean grease is

seen.

Use Texaco

®

Starplex II grease.

Wipe off excess grease.

Excess grease will

attract dirt. Always clean tip of grease
gun fitting and grease fitting on machine
before attaching hose to prevent dirt from
being forced into machine parts.

JACKSHAFT BEARING GREASE FITTING

ENGAGEMENT HANDLE GREASE FITTING

ENGINE SLIDE GREASE FITTING

«
...
44
45
46
47
48
...
»

Содержание 3500D


































































































































Отзывы:

Нет отзывов