Carlton 3500D Скачать руководство пользователя страница 25

Страница: 25 / 129

3500D MACHINE FEATURES

(Remote machine shown here.)

•

Direct hydraulic drive
pump.

•

Low Maintenance
drive belts.

•

Self-purging roller
bearings.

•

Counterbalance valves.

•

Replaceable rod ends.

•

Hardened bushings.

•

Blanchard ground 1”
thick cutter wheel

•

Carbide tipped teeth.

•

Center lube spindles.

•

Belt Guards.

•

Rubber and Metal chip
guards.

•

Control guards.

•

Optional hour meter.

•

Optional Key switch.

•

High quality epoxy
primer.

•

Dupont Imron

Finish.

•

Optional Remote
control.

•

Double wire braid
hydraulic hose.

•

Large fuel tank.

•

Large hydraulic oil
reservoir.

•

High capacity battery.

•

Marine Battery Box.

•

Heavy plate fenders.

•

Premium flotation
tires.

•

Swivel Jack stand with
steel wheel.

•

Hitch and safety
chains.

•

Optional Shake Proof
Towing lights with
coiled wiring harness.

•

Hydraulic or electric
brakes (Optional).

•

Factory tested.

We Pride Ourselves

in the strength and quality of each and every machine

Содержание 3500D


































































































































Результаты поиска

Содержание 3500D

Отзывы:

Carlton 3500D, Руководство пользователя, Страница: 25 / 129

Результаты поиска

Содержание 3500D

Отзывы: