manualshive.com logo in svg

Carl Valentin C220, Инструкция по эксплуатации

Поделиться
Скачать
Carl Valentin C220 Скачать руководство пользователя страница 31

C220 / C300 / C400 

Troubleshooting 

 

03.22 

Service Instructions 

31 

 

 

Error 

Cause 

Solution 

Loss of blow air 

The valve is not activated. 

The LED at the valve does not 
glow. 

Defective applicator PCB. 

Change the applicator PCB. 

Insufficient pressure at pad with 
an activated valve. 

Defective pneumatic tubes. 

Replace the pneumatic tubes. 

Loss of applicator function 

Compressed air failure. 

Check the connections. 

Defective applicator PCB. 

Change the applicator PCB. 

Loss of support air 

Valve is not controlled. 

Defective applicator PCB. 

Change the applicator PCB. 

Insufficient pressure at blow 
tube with an activated valve. 

Defective pneumatic tubes. 

Change the pneumatic tubes. 

Defective or wrong adjusted 
throttle valve. 

Adjust and/or change the 
throttle valve. 

Permanent error at the label 
transfer via pad 

Faulty pad position in transfer 
position to the peel off edge of 
the printer. 

Correct position (backward 
edge of pad approx. 1 mm 
above the peel off edge of 
printer). 

Insufficient or missing vacuum. 

Adjust the vacuum at throttle 
valve. 

Support air does not blow 
exactly the label to the pad. 

Adjust the blow tube. 

Adjust the pressure of support 
air via throttle valve 'support 
air'. 

Adjust the switch on delay. 

 

Содержание C220













































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды