Carel HeaterSteam 4 UR002, Руководство пользователя

Страница: 15 / 92

15
ENG
“heaterSteam” +0300087EN - rel. rel. 1.4 - 22.01.2021
Key:
1. L-shaped mounting bracket (where applicable)
2.
fl ange gasket
3.
steam inlet (ØA)
4. condensate drain (ØB)
5.
fl ange screw (see instructions sheet that comes with the distributor)
6.
L = length (depending on the model of distributor, see paragraph
“Linear distributors” )
7. tilt angle (about 2 °) for condensate drain
8.
diameter of the hole in the wall (ØY)
Size in mm (in)
linear distributors from CAREL
DP***D22R0 DP***D30R0 DP***D40R0
ØA 22 (0.9) 30 (1.2) 40 (1.6)
ØB 10 (0.4) 10 (0.4) 10 (0.4)
ØY 58 (2.3) 68 (2.7) 89 (3.5)
Ø 35 (1.4) 45 (1.8) 60 (2.4)
X 68 (2.7) 77 (3.0) 99 (3.9)
Tab. 3.a
Caution:
1.
mount the distributor slightly tilted (at least 2°, to facilitate the
condensate discharge);
2. the L-shaped supports (see element 1 Fig. 3. b) is supplied with steam
distributors models from DP085* to DP205*. For shorter lengths the
bracket can be supplied as optional (code 18C478A088).
3.3 CAREL high-effi ciency linear distributors
for air ducts or AHUs (DP***RH)
CAREL high-effi ciency linear distributors can be used wherever there is
the need to reduce condensate formation within the distributor itself.
All the information provided in the paragraph on linear distributors
still applies, while the dimensions and diameters corresponding to the
DP***RH distributor are shown below.
6
B
Y
X
A
X
°2
1
1
2
4
3
5
7
8
Fig. 3.b-1
Key :
1. “L” shaped fi xing bracket (where featured)
2.
fl ange gasket
3. steam inlet (ØA)
4. condensate drain (ØB)
5.
fl ange screw (see the technical leafl et supplied with the distributor)
6.
L = length (depending on the distributor models, see the paragraph
on “Linear distributors”)
7.
slope (about 2°) for condensate drainage
8.
diameter of the hole in the wall (ØY)
Dimensions in mm (in)
CAREL high-effi ciency distributors
DP***D30RH DP***D40RH
ØA 30 (1.2) 40 (1.6)
ØB 10 (0.4) 10 (0.4)
ØY 68 (2.7) 89 (3.5)
Ø 45 (1.8) 60 (2.4)
Ø1 60 (2.4) 80 (3.1)
X 77 (3.0) 99 (3.9)
3.4 CAREL blowers for room installation
(VSDU0A*, VRDXL*)
Steam distributors for installation in rooms. These come with a fan
to assist steam absorption. The VSDU0A* blowers can be used on
humidifi ers with fl ow-rates up to 18 kg/h (39.7 lb/h), i.e. models UR002…
UR013. They can be connected to the top of the humidifi er, or separately
in a remote position using the fastening support VSDREM0003 (see Fig.
3.c). These distributors have a power supply inside the electrical panel (24
Vac, Terminals X1, X2).
30222190_002_R01
A
D
D
B
C
D
D
B
C
E
A
Fig. 3.c
Assembly (all dimensions in m [ft])
Ref.
On top of the humidifi er Wall
A > 3 (9.8) > 3 (9.8)
B >1 (3.3) >1 (3.3)
C around 2.1 (6.8) around 2.1 (6.8)
D > 0.5 (1.6) > 0.5 (1.6)
E - ≤4 (13.1)
Tab. 3.b
Note:
•
the value of C may be lower when transiting in front of the blower is
not possible;
•
see the humidifi cation manual for details on positioning
Caution: in order to achieve proper steam distribution observe
the distances indicated in the fi g. above.
For the humidifi ers larger than 18 kg/h, the are ventilated steam
distributors code VRDXL00000 with 230 Vac power supply, external
power supply (maximum capacity 45 kg/h). The distributors are designed
for installation in a remote position, and require two steam hoses with a
30 mm diameter, c. Connected to a “Y” adapter (available as accessories,
contact Carel for details on the product code).
30222195_002_R01
D
D
B
C
E
A
Fig. 3.d
Assembly (all dimensions in m [ft])
Ref.
Wall Ref. Wall
A >5 (16.4) D > 0.5 (1.6)
B ≥2 (6.5) E ≤4 (13.1)
C+E ≥2.1 (6.8)
Tab. 3.c
Note:
•
the value of C+E may be lower when transiting in front of the blower
is not possible;
•
see the humidifi cation manual for details on positioning
In this case, terminal J19.1 on the control board is used as a voltage-free
contact (normally open when there is no production - SSR OFF).
T h is
c on tact ha s a m a ximum r at in g of 2 A.