Carefree Universal Eclipse Скачать руководство пользователя страница 23

Страница: 23 / 23

Carefree of Colorado

Installation

Manual

CLIPSE

052568-001r5

OWER

ONNECTION FOR OPTIONAL

OEM

RGB

LED'

The RGB LED uses a receiver and remote (SR0109).

NOTE:

The installation requires that the power line (+12VDC) be attached to a dedicated 2A circuit

breaker or a 2A in-line fuse must be installed between the control module and power source. Locate the
fuse for easy access. Fuse and connector are furnished by the installer.

1. Route the power cable into the vehicle with the motor cables from the awning.

2. Route the Red wire to +12Vdc.

3. Route the Black wire to ground.

4. Ensure that the connections are tight, solid and sealed when completed.

5. For awning rail applications:

5.1. Mount the control module and RF sensor on the outside of the vehicle as shown using double

sided tape.

5.2. Connect the module wires to the power harness and LED strip.

NOTE:

The LED connector and receiver connectors must be oriented with the arrows on the

connectors lined up. The lights will not work if the connectors are not properly oriented.

arLED005

Receiver
Module

OFF

FLASH

STROBE

FADE

SMOOTH

Power Harness

Route into Vehicle
with Motor Wire

Receiver

Attach to Side of Channel

with Double Sided Tape

LED Strip
at Awning Rail

IR Sensor

Attach to Vehicle Wall
with Double Sided Tape

Vehicle Wall

Red

+12VDC

GND

18awg Wire

(minimum)

Red

Black

Power Harness

LED Strip

Infrared Sensor

Polarity Alignment:

Align Arrows

on Connectors

Awning Rail Mount

Remote

Allow 3"-4" of
Harness to Extend
Past Top of Arm

2A In-line Fuse

(+12VDC Line)

Содержание Universal Eclipse
























Результаты поиска

Содержание Universal Eclipse

Отзывы:

Похожие инструкции для Universal Eclipse

Бренды по названию

Популярные бренды

Carefree Universal Eclipse, Руководство по установке

Результаты поиска

Содержание Universal Eclipse

Отзывы:

Похожие инструкции для Universal Eclipse

Бренды по названию

Популярные бренды