manualshive.com logo in svg

Carefree Universal Eclipse, Руководство по установке

Поделиться
Скачать
Carefree Universal Eclipse Скачать руководство пользователя страница 7

Carefree of Colorado

 Installation 

Manual 

E

CLIPSE

 

052568-001r5 

3 

  I

TEM

 D

ESCRIPTION

 

Q

TY

  N

OTE

 

1 

Rollbar Assembly 

1 

 

 

2 

Screw, HWHC 

#6 x 3/8

2 

 

 

3 

Tractioner 

2 2 

 

4 

Screw, Truss Head, SQ Drive 

#10 x 5/8

2 

2 

 

5 

LH Arm Assy, Idler 

1 

 

 

6 

RH Arm Assy, Motorized 

1 

 

 

7 

Fascia Assy 

2  

 

8 

Bottom Cover 

2  

 

9 

Screw, Lag 

1/4 x 1 1/2

8 

 

 

10 

Screw, Truss Head, SQ Drive 

#10 x 5/8

4 

 

 

11 

Screw, SHC, Self-Tapping 

#8 x 3/4

4 

 

 

12 

Screw, HWHC 

#6 x 3/8

2 

 

 

13 

Jumper Cable 

1 5 

 

15 

Rail Extension Kit 

1 

3,4 

 

16 

Screw, SHC 

#10 x 1/2

4 

3,4 

 

17 

Nylock Nut 

10-32

4 

3,4 

 

18 

Screw, Lag 

1/4 x 2 1/2

8 

3 

 

19 

Rivet, Moly 

7/32

4 

3 

 

20 

Switch Kit, Single Switch 

1 

6 

 

21 

Control Box, Direct Response 

1 

 

 

22 

Screw, Phillips Truss Head 

#6 x 1/2

2 

 

 

23 

Harness, Power, Motor 

2 

 

 

24 

Switch Kit, Direct Response 

(includes bezel and connector harnesses)

1 

 

 

25 

Receiver, RF, 433 MHz  

1 

 

 

26 

Screw, Phillips Truss Head 

#6 x 1/2

2 

 

 

27 

Cable 

60”

1  

 

28 

Remote Control Key FOB, 433MHz 

1 

 

 

29 

Cable 

60”

2  

 

30 

Sensor, Ignition Lock-Out 

1 

 

 

31 

Splitter 

1  

Notes: 

1.  Awning configuration is specified at time of order, including awning length, fabric, color and 

electronics.  Check awning assembly against original purchase order. 

2.  Screws and Tractioners are furnished with roller tube assemblies equipped with optional 

Alumaguard/Uniguard. 

3.  Used with aftermarket installations. 
4.  Rail Extension kit includes hardware for two arms (items 15, 16,17).  Standard for 

aftermarket installations. 

5.  Place Jumper Cable (item 14) with RV owner information.  Installation manual, if included, 

is for installer reference. 

6. OEM's 

may

 

choose to furnish the control switch (item 20).  The switch must be a DC 

polarity reversing switch with dynamic brake. 

Содержание Universal Eclipse
























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды