Carefree Freestyle RM Скачать руководство пользователя страница 8

Страница: 8 / 25

Carefree of Colorado Service

Manual

REESTYLE

070014-301r6

ANOPY

EPLACEMENT

RIGINAL

ONFIGURATION

)

This procedure requires two people.

1. Open the awning 18"-24".

2. Disconnect power to the awning.

3. Carefully push the lead rail toward the case so that the arms collapse and

the fabric is slack.

4. Hold the lead rail in this position and firmly tie the elbows of the spring arms

together. Use a minimum 1/2" rope - do not use bungee cords. When tying
the rope, use a non-slip knot such as a square knot or equivalent.

CAUTION

Failure to secure the lead rail as described will allow the spring arms to

unexpectedly extend out possibly causing personal injury and damage to the awning.

1. On the LH (motor) side:

1.1. Remove the fabric retaining screw from the

lead rail endplate.

1.2. Remove the two cover screws. Do not

remove the motor or end cap.

2. On the RH (idler) side:

2.1. Remove the lead rail end plate.

2.2. Remove the idler endcap and set aside.

2.3. Rotate the cover back and out of the way.

3. Pull the roller tube out the idler end of the case while pulling the fabric from the lead rail. Pull the roller tube

straight, do not allow the roller tube to bend or twist.

4. Note the orientation of the old canopy then unwrap and remove from the roller tube.

5. Unfold the replacement fabric then slide the new fabric onto the roller tube and center.

NOTICE

While the awning fabric is fairly robust, use care not to snag the new fabric while

sliding it into the roller tube and lead rail.

Tip: Lightly spraying the slots with a dry silicone lubricant will help the fabric slide into the slots without
staining the material.

6. Roll the canopy onto the roller tube leaving enough fabric to reach between the case and the lead rail.

7. Slide the fabric into the lead rail and the roller tube into the case.

8. Align the roller tube with the motor drive and bearing.

9. Support the roller tube and attach the RH end cap while aligning the RH end of the roller tube with the

end cap bearing. It is not necessary to close and attach the cover at this time.

10. Open and close the awning to confirm that the fabric rolls and unrolls squarely. Adjust the fabric

position in the lead rail as required.

11. Attach the RH lead rail end plate.

NOTE:

The top screw secures the fabric in the lead rail. The screw should be positioned to thread into

the metal of the lead rail and the edge of the polycord.

12. Attach the fabric retaining screw into the LH lead rail end plate.

13. Close and secure the cover. There are two screws on each end of the awning.

14. After installing the canopy, it may be necessary to adjust the motor limits. Refer to "Adjusting the Motor

Limits" on page 3.

RMF033b

Fabric Retaining

Screw

Cover

Screws

Leadrail

Endplate

Idler

Endcap

Cover

FRM007

Spring Arms

Firmly Tie Elbows Together

Содержание Freestyle RM


























Результаты поиска

Содержание Freestyle RM

Отзывы:

Похожие инструкции для Freestyle RM

Бренды по названию

Популярные бренды

Carefree Freestyle RM, Руководство по обслуживанию

Результаты поиска

Содержание Freestyle RM

Отзывы:

Похожие инструкции для Freestyle RM

Бренды по названию

Популярные бренды